325 mm
2 m
10 mm
Min
.
25
cm
Min
.
25
cm
Min. 20 cm
Min. 2 m
•
The power cable, the main switch and the plug are perfectly intact.
If any damage is found, of any entity or type, interrupt the installation procedure and contact the
retailer or the manufacturer for the appropriate reports.
The position of the product must be chosen so that it cannot be hit by water, steam jets or corrosive
liquids. Check that the air humidity conditions in the room are between 20% and 80%. Make sure
that there are no electrical cables or other installations (water pipes or other technological systems)
near the area identified for the holes. Also check that the wall support identified is sufficiently strong
to support the device.
Drill two holes in the wall at a minimum height of 2 m from the floor and at least 30 cm from a corner
wall, with a diameter suitable for the expansion plug contained in the package. The holes should
have a distance of 325 mm (32.5 cm) between them. Then screw the self-tapping screws included in
the package letting them protrude 10 mm (1 cm) from the wall, then hook the device.
INSTRUCTIONS FOR USE
If any unforeseen anomaly occurs during the use of the device, it is recommended to perform the
following procedure:
1.
Turn it off using the rear switch;
2.
Disconnect it from the power supply;
3.
Contact your dealer or manufacturer immediately.
Once the device is positioned on the wall, insert the plug into the electrical socket and operate the
rear switch. When switched on, the device will show all the lights on the LED display and then only
the “ON / OFF” symbol in the static position.
1.
Turn on the fan by pressing the “ON / OFF” button on the remote control, at this point the
device will emit simple air at room temperature showing the fan symbol on the LED display;
2.
Press the + button repeatedly until the second number on the display shows “49”;
3.
Restart the device by pressing the “ON / OFF” button twice;
4.
Press the “MODE” button on the remote control. The sanitizing device will operate continuously
(a blue reflection will be visible from the air outlet grille);
5.
Press the “MODE” button twice again to deactivate the sanitation and return the device to fan
mode;
6.
Press the “ON / OFF” button on the remote control to turn off the device at any time.
The fan
will always turn off with a 30 second delay.
Date and time
The date and time can be set only when the device is turned on.
1.
When in operation, press the “SET” button on the remote control. The number “1” will start
flashing on the LED display. Press the + and - buttons to increase or decrease the values from 1
to 7 (1 = Monday; 2 = Tuesday; and so on). Then select the one corresponding to today’s date;
2.
Press the “SET” button again and the first two numbers will start blinking. Press the + and -
buttons to increase or decrease the values from “01” to “00” (01 = one in the morning; 12 =
noon; 00 = midnight). Then set the value corresponding to the current HOURS;
3.
Press the “SET” button again and the second two numbers will start flashing. Press the + and -
buttons to increase or decrease the values from “00” to “59”. Then set the value corresponding
to the current MINUTES. Wait a few moments and the settings will be confirmed.
24H Timer Function
Allows you to set a number of operating hours after which the device switches off automatically. The
function can only be selected when the device is turned on.
1.
Press the “24H” button on the remote control. The LED display will show flashing “00:00”. The
“D” indicator will light up on the display;
2.
Continue to press the “24H” button to increase the operating hours from 01:00 to 24:00 (01:00
= 1 hour of operation; 02:00 = 2 hours; and so on). Wait a few moments and the settings
will be confirmed. After a few minutes of operation, the “D” warning light will switch off
automatically from the display but the function will remain active;
3.
By selecting the value 00:00 the timer is deactivated and the warning light D will switch off on
the display.
The 24H Timer function sets the operating hours of the device according to the operating mode
(fan only or fan + sanitizer). The 24H Timer function does not automatically activate the sanitation
function. Activate the sanitization with the “MODE” button on the remote control if you also want to
activate this function.
Open Window Function
Through this function, the device is able to detect the ambient temperature and will stop
automatically if it drops below 3°C. The function can only be selected when the device is turned on.
1.
Press the “AUTO” button on the remote control and the “Window Open” indicator will light up
on the LED display. The device will operate using a power saving mode;
2.
To deactivate the function, press the “AUTO” button again and the “Window Open” indicator
on the display will go off.
Weekly Program Function
Allows you to set an operating time band for each day of the week. The function can be selected
only when the device is switched on and after having previously set the current date and time (see
paragraph “Date and Time”). The operation consists of two phases.
FIRST PHASE:
1.
Press the “W-TIMER” button on the remote control. The number “1” will start flashing on the
display. Press the + and - buttons to increase or decrease the values from 1 to 7 (1 = Monday;
2 = Tuesday; and so on). Then select the one corresponding to the day of the week you want to
set. Do not consider the “W”, “ON” and “OFF” lights possibly present on the LED display;
2.
Press the “W-Timer” button again and you can set the device switch-on time with the + and -
keys, then press the “W-Timer” button again to set the minutes;
3.
Press the “W-Timer” button again and you can set the device shutdown time with the + and -
keys, then press the “W-Timer” button again to set the minutes.
4.
Pressing the “W-Timer” button again will move to the day following the one just set. Wait a
few moments and the settings will be confirmed;
5.
Restart the device by pressing the “ON / OFF” button on the remote control twice.
Then complete the setting for all days of the week, from 1 to 7. If you want the device not to start, set
“00:00” for both the switch-on time and the switch-off time. In the event that the setting procedure
is interrupted by the user, it can be resumed at any time since the settings will remain in memory.
SECOND PHASE:
6.
Press the “W-TIMER” button on the remote control. The LED display will show the “W”
indicator, signaling the ignition in the Weekly Program mode;
9