background image

To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.

Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche
polarisée (une des lames est plus large). Cette fiche ne peut être insérée dans une
prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire
installer une prise adéquate par un électricien qualifié. Ne pas modifier la fiche.

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or
sharp objects with the cleaner to prevent bag tears, hose clogs, and fan blade breakage
with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional
service information telephone our toll free number for the nearest Eureka/Sanitaire
Authorized Warranty Station. You should know the model, type and serial numbers
when you call:

USA: 1-800-282-2886

Mexico:  5670-6169

Canada:  1-800-282-2886

If you prefer, you can write to The Eureka Company, Service Division, 807 North Main
Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company,
866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Sanitaire Limited Warranty
for complete service information.

DO NOT OIL the motor or the brush roll at any time.  The bearings are
permanently lubricated and sealed.

Rating Plate

The model, type, and serial numbers are
indicated on the rating plate located on the
underneath side of the cleaner. For prompt and
complete service information, always refer to
these numbers when inquiring about service.

Model & Type_________________________

Serial No.____________________________

4

SERVICE INFORMATION: 1-800-282-2886

MODEL               TYPE               SERIAL NO.

VOLTS                    AMPS.                     HERTZ

Содержание 670 Series













Отзывы: