Sanijet PIPELESS SSB2-S115-XX страница 12 Скачать руководство пользователя

Страница: 12 / 16

Operating Instructions

1. After the pedicure bath has been properly installed, fill the unit with water, at the desired temperature, 1 in (3 cm) above

the jets.

2. Verify that the unit’s electrical cord is connected to a GFCI protected electrical outlet.

3. To start or stop this appliance turn the dial switch to the ON or OFF position.

4. Bath additives , including oil based products , can be used in a SANIJET Pipeless™ Pedicure Bath, since their residue can

be easily cleaned. CAUTION: Use only low foaming additives, and do not use products that contain sand or silicates.

5. You should always be in a seated position when placing your feet into or removing them from the pedicure bath.
WARNING: NEVER STAND IN THE PEDICURE BATH BASIN.

Quarter-turn Counter Clockwise

Содержание PIPELESS SSB2-S115-XX

















Результаты поиска

Содержание PIPELESS SSB2-S115-XX

Отзывы:

Похожие инструкции для PIPELESS SSB2-S115-XX

Бренды по названию

Популярные бренды

Sanijet PIPELESS SSB2-S115-XX, Руководство пользователя

Результаты поиска

Содержание PIPELESS SSB2-S115-XX

Отзывы:

Похожие инструкции для PIPELESS SSB2-S115-XX

Бренды по названию

Популярные бренды