SANEI ELECTRIC SK1-21 Скачать руководство пользователя страница 38

Страница: 38 / 60

３８

SK1-21/31

4- 4

．

Setting the memory switch

Follow the flow chart to change the parameter. As the setting parameter is printed, choose the right
parameter by manipulating the FEED and SELECT buttons.

After completing the parameters set up, data are stored and the printer goes to standby mode.

ENTER SETTING ?

ENTER COMMON

SETTING ?

ENTER INTERFACE

SETTING ?

Change the setting of INTERFACE

・

BAUD RATE

・

BIT LENGTH

:
:

MODE END

(Finish)

Change the setting of COMMON

ＰＡＰＥＲ

FEED

Function setting mode

YES

※

Prints the below after

completing the setting:
SETTING COMPLETE
SETTING MODE END.

※

The setting mode is

finished and the printer goes
to standby mode.
Modified data are stored
automatically.

YES

■

YES : FEED button

------

Decide

■

NO : SELECT button

------ Move to next

Содержание SK1-21





























































Результаты поиска

Содержание SK1-21

Отзывы:

Бренды по названию

Популярные бренды

SANEI ELECTRIC SK1-21, Техническое руководство

Результаты поиска

Содержание SK1-21

Отзывы:

Бренды по названию

Популярные бренды