S&T Kontron KBox E-410-APL Скачать руководство пользователя страница 63

Страница: 63 / 78

KBox E-410-APL - User Guide, Rev. 1.0

www.kontron.com

// 63

Figure 28: BIOS Advanced Menu - SATA Configuration

BIOS SETUP UTILITY

Main

Advanced

Power

Boot

Security

Save & Exit

SATA Configuration

SATA Controller(s)

[Enabled]

→

←

: Select Screen

SATA Mode Selection

[AHCI]

↑

↓

: Select Item

Enter: Select

Serial ATA Port 1

[Not Installed]

+/-: Change Opt.

Port 1

[Enabled]

F1: General Help

mSATA Port 1

[Not Installed]

F2: Previous Values

Port 1

[Enabled]

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Feature

Option

Description

SATA Controller(s)

[Enabled], [Disabled]

Select whether to enable or disable SATA controller.

SATA Mode Selection

[AHCI]

Determine how SATA controller(s) operate.
Note: Device driver support is required for AHCI or RAID.
Depending on how the hard disk image was installed, changing
this setting may prevent the system from booting.

Port 1

[Disabled], [Enabled]

Select whether to enable or disable SATA Port 1 or mSATA Port 1.

Содержание Kontron KBox E-410-APL















































































Результаты поиска

Содержание Kontron KBox E-410-APL

Отзывы:

S&T Kontron KBox E-410-APL, Руководство пользователя, Страница: 63 / 78

Результаты поиска

Содержание Kontron KBox E-410-APL

Отзывы: