manualshive.com logo in svg

Sandpiper S07, Оригинальное руководство пользователя

Поделиться
Скачать
Sandpiper S07 Скачать руководство пользователя страница 18

s07nmdl1sm-rev0817

sandpiperpump

.

com

Model S07 Non-Metallic • 

15

Pilot Valve Assembly

PILOT VALVE ASSEMBLY PARTS LIST

ITEM  PART NUMBER 

DESCRIPTION 

QTY

3 

095-091-000 

Pilot Valve Assembly 

1

3-A 

095-087-551 

Valve Body 

1

3-B 

755-051-000 

Sleeve (With O-rings) 

1

3-C 

560-033-360 

O-ring (Sleeve) 

6

3-D 

775-055-000 

Spool (With O-rings) 

1

3-E 

560-023-360 

O-ring (Spool) 

3

3-F 

675-037-080 

Retaining Ring 

1 

 

PILOT VALVE SERVICING 

To service the pilot valve first shut off the 

compressed air supply, bleed the pressure from 

the pump, and disconnect the air supply line 

from the pump.

 

STEP #1:

 See pump assembly drawing.

Using a 7/16" wrench or socket, remove 

the four capscrews (item 12). Remove the air 

inlet cap (item 8) and air inlet gasket (item 18). 

The pilot valve assembly (item 3) can now be 

removed for inspection and service.

S T E P   # 2 :

  D i s a s s e m b l y   o f   t h e  

pilot valve.

Remove the pilot valve spool (item 3-D). 

Wipe clean and inspect  spool and o-rings for 

dirt, cuts or wear. Replace the o-rings and spool 

if necessary.

Remove the retaining ring (item 3-F) from 

the end of the sleeve (item 3-b) and remove 

the sleeve from the valve body (item 3-A). Wipe 

clean and inspect sleeve and o-rings for dirt, 

cuts or wear. Replace the o-rings and sleeve 

if necessary.

S T E P  # 3 :

  R e - a s s e m b l y   o f   t h e  

pilot valve.

Generously lubricate outside diameter of 

the sleeve and o-rings. Then carefully insert 

sleeve into valve body. Take CAUTION when 

inserting  sleeve,  not  to  shear  any  o-rings. 

Install  retaining  ring  to  sleeve.  Generously 

lubricate outside diameter of spool and o-rings. 

Then carefully insert spool into sleeve. Take 

CAUTION when inserting spool, not to shear 

any  o-rings.  Use  BP-LS-EP-2  multipurpose 

grease, or equivalent. 

STEP #4:

 Re-install the pilot valve 

assembly into the intermediate.

Be careful to align the ends of the pilot 

valve stem between the plunger pins when 

inserting the pilot valve into the cavity of the 

intermediate.

Re-install the gasket, air inlet cap and 

capscrews. Connect the air supply to the pump. 

The pump is now ready for operation.

4: AIR 

END

Содержание S07
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды