12
Fitting to a wooden beam
Four screws
(H)
are supplied together with safety washer’s
(I)
for fitting the support plate
(A)
to a
wooden beam. The holes for the screws should not be of greater diameter than the diameter of the
screw. Ensure that the wooden beam is able to support the weight of the moving fan
(minimum 25/40 Kg.) (Fig.
4
ASSEMBLY OF THE FAN
IMPORTANT
: If you installing more than one fan, ensure that you do not mix the fan blade sets, even
though they are from the same ceiling fan model.
the plate a minimum of six times, so that at least some of the turns pass through the groove in the
crossbeam. Secure the wire by twisting it around itself several times.
Ensure that the ceiling is able to support the weight of the fan when in operation (
minimum
25/40 Kg.). (Fig.
3)
1. Fit the blades
(C)
to the motor assembly and support
(B)
using the blade fitting screws
(D)
and the
safety washers
(E)
. Do not forget to use the felt protection washers
(J)
between the blade and the
motor assembly to avoid possible noise. Repeat this process with the remaining blades.
(F
i
g. 5)
IMPORTANT
:
Be careful not to support yourself on the fan blades, as these could then become
unbalanced and cause vibration or shaking of the fan.
2. Loosen the screws situated in the base of the decorative canopy to allow easier access to the
anchorage point and electrical connectors. Hang the motor and support assembly
(B)
from the
hook on the support plate
(A)
(previously fixed to the ceiling)
(F
i
g. 6)
3. Connect the cables and position them correctly. The connections and the fitting point can be
hidden using the decorative canopy. Fix the two screws situated in the base of the decorative
canopy.
- The wiring connection to connect the speed regulator supplied with the fan, is indicated in the
Figure 7.
- With the switch can be change airflow direction
(F
i
g. 8)
.
IMPORTANT
:
Before changing the direction of ariflow, the fan blades must have completely stopped
turning after switching the unit to the off position.
INSTALLATION ELECTRICAL
IMPORTANT SAFETY NOTICE:
Before installation, ensure that the electrical supply is disconnected
at the mains junction / fuse box.
IMPORTANT NOTE
:
S&P has a remote control kit (RC HTB) which is sold separately. This kit (RC
HTB) facilitates the fan installation, as it avoids electric cabling to the speed regulator, supplied as
standard.
(F
i
g. 1F)
.
With the remote control, can switch ON/OFF the fan and adjust the speed. Also, incorporates a
TIMER.
Содержание HTB-140 RC
