S&C Remote Supervisory Vista Скачать руководство пользователя | Manualshive

Страница: 28 / 32

background image

28 S&C Instruction Sheet 682-510

Maintenance

Figure 51. Lock the outer and low-voltage enclosures.

Padlock

Operation compartment

Low-voltage
enclosure

Front panel

Front panel

Termination compartment

Figure 52. S&C touch-up finish and red-oxide primer. Order by
catalog number 9999-058 for olive green finish, 9999-080 for
light gray finish, and 9999-061 for red-oxide primer.

Touch-up

finish

Red-oxide

primer

Returning Equipment to Service

When returning the equipment to service, the following
procedures should be observed:

STEP 1.

Make sure the load-interrupter switch and
fault-interrupter grounding means are
removed.

STEP 2.

Make certain the load-interrupter switches and
fault interrupters are in the cor rect

Open

or

Closed

positions.

STEP 3.

If a pad-mounted enclosure is furnished, close
and padlock the termination compartment
before energizing the circuit and operating any
switching devices.

STEP 4.

Padlock the switchgear and low-voltage com-
partment or enclosure before leaving the site—
even momentarily. See Figure 51. Observe this
procedure even in those cases where the gear is
accessible only to qualifi ed persons.

Enclosure Finish

The responsibility for ensuring that the fi nish protects
the enclosure lies with both the man ufacturer and
the user. Enclosures provided are fi nished with S&C’s
Ultradur® II Outdoor Finish, which provides lasting
protection. To retain this protection, the user should take
periodic corrective action as follows:

STEP 1.

Touch-up any penetration of the fi nish to bare
metal—such as scratches and abrasions
caused by shipping or vandalism—to maintain
the original integrity. S&C touch-up fi nish and
primer are available in aerosol spray cans. See
Figure 52. No other fi nish or primer is approved.
The area to be touched up should be cleaned to
remove all oil and grease. Sand the area,
removing any traces of rust that may be present,
and make sure all edges are feathered before
applying primer.

STEP 2.

Provide an occasional simple wash

down—

such as an automobile would be given—to
remove surface contaminants. Use any
ordinary mild household detergent solu tion.

STEP 3.

In those cases where the enclosure must be
refi nished by the user before the fi nish has
weathered—for example, to match other
equipment—a special precaution must be
taken. The entire surface must be sanded to
provide a tooth to bond the new coat to the S&C
Ultradur II Outdoor Finish.

«
...
26
27
28
29
30
...
»

Содержание Remote Supervisory Vista

































Отзывы:

Нет отзывов

Похожие инструкции для Remote Supervisory Vista

Бренд: e2-live Страницы: 12

3C10220 - Ethernet Power Source Supply

Бренд: 3Com Страницы: 44

Server Technology PRO3X

Бренд: LEGRAND Страницы: 182

Бренд: ICM Controls Страницы: 2

Бренд: Tripp Lite Страницы: 4

Бренд: Kikusui Страницы: 144

Бренд: Dataprobe Страницы: 72

Бренд: GE Digital Energy Страницы: 502

Бренд: Abtus Страницы: 2

MULTICLUSTER BOX 36

Бренд: SMA Страницы: 48

MULTICLUSTER-BOX 12

Бренд: SMA Страницы: 54

Бренд: POINT POD Страницы: 14

Бренд: EtiamPro Страницы: 11

versalogic VersaNet

Бренд: ASA Electronics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды