S&C Remote Supervisory Vista Скачать руководство пользователя | Manualshive

Страница: 23 / 32

background image

S&C Instruction Sheet 682-510 23

Operation

The presence of a dot

in TEST window indi-

cates the VOLTAGE

indicator is in Test

mode

Figure 42. The VOLTAGE indicator is operating properly if a dot
appears in TEST window and a flashing lightning bolt appears
in each PHASE indicator.

Test circuitry can be powered

by flashlight or bright sun

Figure 41. Place a gloved finger over the TEST button to begin
testing.

STEP 3.

Test the VOLTAGE indicator for proper
operation as follows:

(a) Shine a fl ashlight approximately 4 inches (102

mm) above the photocell, and simultaneously
cover the TEST button with a gloved fi nger. See
Figure 41. When the sun is shining brightly, it can
be used to power the test circuit.

(b) If a dot

appears in the TEST window and a

fl ashing lightning bolt

in each of the three

PHASE indicators, then the VOLTAGE indicator
is operating properly. See Figure 42.

«
...
21
22
23
24
25
...
»

Содержание Remote Supervisory Vista

































Отзывы:

Нет отзывов

Похожие инструкции для Remote Supervisory Vista

Expert Power Control 8221 Series

Бренд: GÜDE Страницы: 115

Бренд: Panamax Страницы: 2

Бренд: Rittal Страницы: 77

Бренд: American Audio Страницы: 28

Бренд: GW Instek Страницы: 285

C3Manager-Compax3H

Бренд: Parker Страницы: 16

Pow-R-Line P1R Series

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 20

Advanced Enclosure Power Distribution Unit (ePDU)

Бренд: Eaton Страницы: 122

Бренд: Leviton Страницы: 2

SmartOnline B020-016 6

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: Smart-Fly Страницы: 2

Бренд: Monacor Страницы: 2

Бренд: MTT Страницы: 4

Бренд: MTT Страницы: 4

Бренд: MTT Страницы: 4

Бренд: Atlas Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды