Samwon Tech Temp 2000 M Скачать руководство пользователя страница 147

Страница: 147 / 181

SAMWONTECH

2nd Edition of TEMP2000M_Series IM : April. 8. 2014 Page 143 / 176

19.2.2 DI error occurrence photo setting

▶

It can be only set when display type is “Picture”.

▶

If internal memory has photo file (BMP), Picture is displayed when DI error occurs.

▶

With SD CARD option, photos can be uploaded and please refer to the [20. User screen].

①

( ) is inactivated since there is no relevant file in internal memory.

②

Picture corresponding to DI among photo files (BMP) saved in SD CARD is displayed.

☞

Only selected files can be uploaded into internal memory.

③

This is the button used to upload files in SD CARD into internal memory.

④

It displays current SD CARD capacity.

☞

It displays only when SD CARD is inserted.

▶

When

(upload) button is pushed in [Fig. 19-10 Display photo setting screen when DI error occurs

-3], only photo files selected ( ) in SD CARD are uploaded into internal memory.

▶

Message which says “Now upload in progress” is displayed at the bottom of screen during upload.

①

②

③

[Fig. 19-8] Display photo setting screen when DI error occurs-1

[Fig. 19-9] Display photo setting screen when DI error occurs-2

④

Содержание Temp 2000 M






















































































































































































Результаты поиска

Содержание Temp 2000 M

Отзывы:

Похожие инструкции для Temp 2000 M

Бренды по названию

Популярные бренды

Samwon Tech Temp 2000 M, Инструкция по эксплуатации

Результаты поиска

Содержание Temp 2000 M

Отзывы:

Похожие инструкции для Temp 2000 M

Бренды по названию

Популярные бренды