background image

Federal Communications Commission (FCC) Notice

This device was tested and found to comply with the limits set forth in Part 15 of the FCC 
Rules. Operation is subject to the following conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any interference received including 
interference that may cause undesired operation. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. 

This device generates, uses, and can radiate radio frequency energy. If not installed and 
used in accordance with the instruction manual, the product may cause harmful interference 
to radio communications. Operation of this product in a residential area is likely to cause 
harmful interference, in which case, the user is required to correct the interference at their 
own expense.

The authority to operate this product is conditioned by the requirements that no 
modifications be made to the equipment unless the changes or modifications are expressly 
approved by SAMSys Technologies. 

Trademarks

SAMSys is a trademark of SAMSys Technologies, Inc. 

HyperTerminal

 is a registered trademark of Hilgraeve, Inc.

Other company, product or service names appearing in this manual may be trademarks or 
service marks of their respective owners.

Содержание SARS MP9112





































Отзывы: