Samsung xpress m282 series Скачать руководство пользователя страница 95

Страница: 95 / 116

4. Troubleshooting

► Error Code

S6–3123

► Error message

This IP address conflicts with that of other system. Check it.

► Symptom

Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no
response when checking the ping test.)

► Troubleshooting method

Change the machine’s IP address.

•

Execute the Samsung Easy Printer Manager program. (Device setting — Network — IP address). Change the
IP address.

•

In case of DHCP or Bootp, reboot the machine to receive a new IP address.

► Error Code

S6–3210

► Error message

Network Failure: #S6-3210. Turn off then on. Call for service if the problem persists

► Symptom

Departments along with wireless module is abnormal.

► Troubleshooting method

1) Turn the machine off, and then turn on.

2) Check the setting is proper – AP setting of wireless lan and printer configuration.

4-34

Содержание xpress m282 series


















































































































Результаты поиска

Содержание xpress m282 series

Отзывы:

Бренды по названию

Популярные бренды

Samsung xpress m282 series, Руководство по обслуживанию

Результаты поиска

Содержание xpress m282 series

Отзывы:

Бренды по названию

Популярные бренды