Samsung WW22N6850Q Скачать руководство пользователя страница 38

Страница: 38 / 52

36 _ Troubleshooting

Information

Type

Infor-

mation

Code

Causes

Corrective Actions

Description of Photo

Cooling

• Washing Temperature sensor

fault

• Description of PL hazard

prevention

• This error occurs if the water

Temperature is more than 50 ˚C in

draining. Check the temperature.

• If the water temperature is normal,

this error is due to a temperature

sensor fault. Replace the washing

heater.

When replacing the washing

heater, take care to prevent water

leakage.

Check the resistance on the Heater.

(For faulty features)
Check the voltages both terminals of the Heater

while washing.
Check 25.19 ~ 27.84Ω on both terminals and the

voltage of the Heater.

Door

(cont.)

dC1
dC2

• Door switch fault
• Main PCB fault

• If a dC error occurs, check

whether it occurs during the Boil

cycle.

- If it is detected that the door is

open, close the door.

• The 220V is directly connected

to the door. Check and repair

the power wire connections and

insulation state.

• Check the door switch. Replace if

faulty.

• Check the main PBA door sensing

circuit. Replace if faulty.

• Check the drain Pump wire

connection.

▶

Type1

The resistance of Nos. 3 and 5 of the DOOR LOCK

SWITCH must be approximately 1000Ω±50%.

3 5

▶

Type2

The resistance of No. 2 and 3 of the DOOR LOCK

SWITCH must be approximately 155~200Ω
( In state of pushing slider)

WW22N6850NX-A2_SM.indb 36

2018/2/1 17:15:51

Содержание WW22N6850Q





















































Результаты поиска

Содержание WW22N6850Q

Отзывы:

Бренды по названию

Популярные бренды

Samsung WW22N6850Q, Руководство по обслуживанию

Результаты поиска

Содержание WW22N6850Q

Отзывы:

Бренды по названию

Популярные бренды