Samsung WW22N6850Q Скачать руководство пользователя страница 31

Страница: 31 / 52

Troubleshooting _ 29

4. TROuBLESHOOTINg

4-1. INfORMATION CODE

►

When an abnormal condition occurs, melody sounds and displays Info. code indications as shown in the

following Info. codes are shown until the status has cleared.

No.

Information

Type

Information

Code

Causes

Corrective Actions

Water Level

- The part of the hose where the water level sensor

is located is damaged (punctured).

-  The hose is clogged with foreign material.
-  The hose is folded.
-  Too much lubricant has been applied to the

insertion part of the air hose.

-  Hose engagement error (disengaged)
-  Part fault (Faulty internal soldering)
-  The water level sensor terminal is disengaged.
-  Main PBA fault

• Water level sensor fault
• The water level sensor terminal

is disengaged

•The part of the hose where the

water level sensor folded

• Main PCB fault.

Motor

The PBA connector terminal is not connected.

The motor spin net is not engaged.

The motor’s internal coil is damaged (short-

circuited or cut)

- Foreign material (a screw) has entered the motor.
- Constrain because of Foreign material between

PULSATOR and BOWL

• Washing motor fault
• Check Washing motor

connector

• Washing motor rotor/stator fault
• Main PCB fault

3C1

- Motor overloaded due to too much laundry (Non

sensing)

- PBA fault

3C2

- The motor driving error from the PBA is weak :

Unstable relay operation, etc.

3C3

- The IPM terminal of the main PBA is not

connected.

- The DD motor cover is out of place.

3C4

-  The PCB housing terminal is not connected.
-  PBA fault
-  DD motor fault

3CP

- PBA fault
- Pulsator motor fault

• Pulsator motor fault
• Main PCB fault

Water Supply

- Foreign material is entering the water supply valve.
- The water supply valve terminal is not connected.

(Wire disconnected)

- The warm water and rinse connectors are wrongly

connected to each other.

- This occurs if the PCB terminal from the drain

hose to the detergent drawer is not connected.

Check whether the transparent hose is folded or

torn.

- This occurs Water pressure is weak, a certain time

delay.

- This occurs Water Valve by freezing in winter

season.

• Water supply valve fault
• Main PCB fault
• Freezing by winter season

4C2

- The water temperature is sensed as higher than

50 ˚C in the Wool or Lingerie courses

Drain

- The pump motor impeller is damaged internally.
- The wrong voltage (220 V → 110 V) is supplied to

the parts.

-  Part fault
-  This occurs due to freezing in the winter season.
-  The drain hose is clogged. (Injection error, foreign

material)

- Clogged with foreign material.
- The water pump terminal is not connected : rubber

band, bills, cotton, hair pins, coins.

• Drain pump fault
• Freezing by winter season
• Check inside foreign material of

drain pump

• Main PCB fault

WW22N6850NX-A2_SM.indb 29

2018/2/1 17:15:49

Содержание WW22N6850Q





















































Результаты поиска

Содержание WW22N6850Q

Отзывы:

Бренды по названию

Популярные бренды

Samsung WW22N6850Q, Руководство по обслуживанию

Результаты поиска

Содержание WW22N6850Q

Отзывы:

Бренды по названию

Популярные бренды