background image

When installing a washer and dryer on the first, or second floor, do not 
exceed this leg adjustment height for stability.

 

Foot Pad for Walking Washer, There 
is one in each package, so order 4 

  

Error Type  

Error Mode  

Details  

LED LCD 

                          
Heater Error  

                           
Hr           
36 

(Heater 

Relay)  

 

This can be a short or a wire disconnected to the heater circuit. This 
can also be problem with the tub contacting the heater or if the wa-
ter in the tub is frozen or there is no water. The error is triggered by 
temperatures above 145C. If the heater has no error, this occurs 
because of a PBA relay malfunction. Check the wiring harness to 
the heater.   

An Hr error occurs if the steam heater, is faulty, replace it. 

 

9E1 

 

EMC Filter issue or a noise spike from an external device 

                      
Overflow error 

                         
OE            

 

Water is supplied continually because the water level detection 
does not work. - Verify the drain is working properly, the water level 
detection does not work and water is supplied continually. Verify the 
water valves shut off fully. Finally check the water level sensor. 

                             
Temperature 
Sensor Error 

29 

 

The washing heater temperature sensor in the tub has an error. 
Check the connections for the washing heater temperature sensor 
connector. 

 

                   
Unbalance 

Error 

                         
dC           
10 

 

Check the type of laundry. Check whether it may cause an unbal-
anced situation.- Educate the consumer in this case, to press 
pause, reposition the load or remove a few items. Press start to 
continue and complete the wash cycle. 

                         
Foaming      
Detected 

                     
SUdS     
Sd 

 

This occurs when too much foaming is detected. It is also displayed 
while foaming is removed. When the removal is finished, the normal 
cycle proceeds. (This is one of the normal operations. It is an error 
for preventing non-sensing faults.) 

Check whether the washing machine is level to the floor with respect to the original position of the washing machine prior 
to service. Doing this now will reduce the need for a redo call and customer dissatisfaction.                                                  
✔ Vibrations can shorten the lifetime of the product. 

Silver Care Kit 

(Silver Care 

PCB) Failure.  

7E 

 

Check Silver Care PCB ,Main PCB & Wire-harness 

Mems or Har- 8E 

 

Check MEMS PCB ,Main PCB & Wire-harness 

 

6

Содержание WF337AAR/XAA








Отзывы: