manualshive.com logo in svg

Samsung WA14V2Q2DW/XAP, Руководство по обслуживанию, Страница: 24 / 32

Поделиться
Скачать
Samsung WA14V2Q2DW/XAP Скачать руководство пользователя страница 24

23

6-1 REPLACEMENT OF MAIN PCB-ASS'Y

1) After opening the right side lower part gap of

the COVER-PANEL in front of the CONTROL-PANEL
and the FRAME by using a coin or a key, disassemble
by pulling toward.

2) Remove 2 COVER-SCREW from the CONTROL-PANEL

by using a pin and then remove a SCREW 3EA as
shown in the figure.

3) Disassemble the CONTROL-PANEL by pushing it

slightly to left as shown in the figure here.

4) Turn the CONTROL-PANEL ASS'Y and remove

SCREW 5EA securing PCB ASS'Y.

5) Lift up the SCREW slightly to the disassembling

direction, it is disassembled.

6) Disconnect the CONNECTOR from ASS'Y PCB.

※

When disassembling CONTROL-PANEL, be careful not to

allow WIRE to get too much tension.

※

When assembling PCB, check if CONTROL-PANEL fixing

HOOK is properly positioned and tighten with screws.
(If not tightened exactly, Select S/W does not operate.)

※

Points to check after replacing PCB-ASS'Y

Check the each part operating status. (Using TEST MODE)

※

How to disassemble shutter

1) After removing from Hook by pulling down the fore of shutter,

and disassemble by pulling forward.

2) When assembling, push until making a sound how to use upward.

6. HOW TO DISASSEMBLE

100

Содержание WA14V2Q2DW/XAP

































Отзывы:

Нет отзывов