Samsung TT17J Series Скачать руководство пользователя страница 9

Страница: 9 / 70

3. Disconnect all connectors on the CRT Socket

PCB.

4. Using a solder iron, disconnect Ground (G2)

on the back of the Video Shield and remove
the Shield Cap.

5. Remove the screw on the front of the Shield

Socket.

6. Desolder the 4 tabs on the CRT Socket PCB

and remove Shield.

7. Place the Video PCB on a flat, level surface

that is protected from static electricity.

3-1-3 Removing the Main PCB

1. Complete all previous steps.
2. Disconnect the Degaussing Coil at GT601 and

GT602 on the Main PCB.

3. Disconnect all easily accessible ground wires

on the Main PCB and Bottom Chassis.

4. Disconnect the DY connector at the CN303

connector on the Main .

5. Remove 2 screws the Main PCB then lift up

the Bottom to separate the two Shield.

6. Remove the screws on the back and along

each side of the Bottom Chassis.

7. Carefully lift the Main PCB Ass’y and remove

the remaining ground wires.

8. Place the Main PCB Ass’y on a flat, level

surface that is protected from static electricity.

3-1-4 CRT Ass’y Disassembly

1. Complete all previous steps.
2. Straighten the Degaussing Coil Assembly

coated metal ties and lift the Coil Ass’y from
the CRT.

3. Remove the four corner screws and lift the

CRT up and away from the Front Cover
Assembly and place it on a padded surface.

Caution: Do not lift the CRT by the neck.

If you will be returning this CRT to
the monitor, be sure to place the CRT
face downward on a protective pad.

3 Disassembly and Reassembly

3-2

TT17J*

Figure 4

3-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

Содержание TT17J Series







































































Результаты поиска

Содержание TT17J Series

Отзывы:

Бренды по названию

Популярные бренды

Samsung TT17J Series, Руководство по обслуживанию

Результаты поиска

Содержание TT17J Series

Отзывы:

Бренды по названию

Популярные бренды