Samsung TT17J Series Скачать руководство пользователя страница 17

Страница: 17 / 70

4 Alignment and Adjustments

4-8

TT17J*

4-3-5 Color Purity Adjustment

Color purity is the absence of undesired color.
Conspicuous mislanding (unexpected color in a
uniform field) within the display area shall not be
visible at a distance of 50 cm from the CRT
surface.

CONDITIONS

Orientation:

Monitor facing east

Scanning frequency:

68 kHz/85 Hz

Display image:

White flat field

Luminance:

Cut off point at the center
of the display area

Note:

Color purity adjustments should only be
attempted by qualified personnel.

PROCEDURE

For trained and experienced service technicians
only.
Use the following procedure to correct minor
color purity problems:

1. Make sure the display is not affected by

external magnetic fields.

2. Make sure the spacing between the PCM

assembly and the CRT stem is 29 mm ± 1 mm.

3. Display a green pattern over the entire display

area.

4. Adjust the purity magnet rings on the PCM

assembly to display a pure green pattern.
(Optimum setting: x = 0.295 ± 0.015,
y = 0.594 ± 0.015)

5. Repeat steps 4 and 5 using a red pattern and

then again, using a blue pattern.

Table 4-4. Color Purity Tolerances

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

6. When you have the PCMs properly adjusted,

carefully glue them together to prevent their
movement during shipping.

Red:

x = 0.640 ± 0.015

y = 0.323 ± 0.015

Green:

x = 0.295 ± 0.015

y = 0.594 ± 0.015

Blue:

x = 0.142 ± 0.015

y = 0.066 ± 0.015

Содержание TT17J Series







































































Результаты поиска

Содержание TT17J Series

Отзывы:

Бренды по названию

Популярные бренды

Samsung TT17J Series, Руководство по обслуживанию

Результаты поиска

Содержание TT17J Series

Отзывы:

Бренды по названию

Популярные бренды