Eng-
USER'S MANUAL
2. PRE ALARM TIME LIMIT
- PRE ALARM recording is a feature that recognizes
what kind of conditions were present immediately
before motion was detected. PRE ALARM TIME
LIMIT can be set to record 5 seconds of video right
before motion detection or an ALARM
occurrence. The System memory always saves up to
5 seconds of video data. When motion is
detected or an ALARM occurs, ALARM recording
starts and PRE-ALARM data is simultaneously
recorded from the System memory to HDD up to the
time length set in PRE ALARM TIME LIMIT.
[0SEC, 5SEC]
- Use
,
,
,
, key to make changes.
3. POST ALARM TIME LIMIT
- Recording is performed up to the time set in MAIN
ALARM TIME. Then data is further recorded up to the
time set in POST ALARM TIME LIMIT.
[10SEC ,0SEC ,0SEC ,1MIN ,MIN ,MIN ,MIN
,5MIN]
- Use
,
,
,
, key to make changes.
4. MOTION DETECTION
- When MOTION DETECTION is set to ON, recording
will start whenever a motion in the input video is
detected.
[ON/OFF]
- Use
,
,
,
, key to make changes.
5. SENSITIVITY
- MOTION DETECTION SENSITIVITY can be set
when user set the MOTION DETECTION.
There are three stages -- HIGH/NORMAL/LOW.
[HIGH/NORMAL/LOW]
- Use
,
,
,
, key to make changes.
6. MOTION CH SETUP
- Set the channel that you want to detect MOTION.
07/07/07 00:00:01
MOTION CH SETUP
CAMERA1
AREA1
CAMERA
OFF
CAMERA
OFF
CAMERA
OFF
CAMERA5
OFF
CAMERA6
OFF
CAMERA7
OFF
CAMERA8
OFF
You can divide the motion detection area into total 9 for
each channel. The following screen displays to activate
only No. 1 area of No. 1 channel.
You can use the direction key to move the area around
and select FULL for the motion detection on the whole
screen. With MOTION DETECTION set to ON, if motion
is sensed in other areas where MOTION DETECTION is
not set to ON, MOTION DETECTION will not operate.
- Motion is detected only from channels set to 'On'.
The following screen shows motion recording after
motion detection. A motion is deteced in the
Channel . The 'M' mark before the title of each
channel indicates that a motion is detected.
[OFF/AREA1/AREA/AREA/AREA/AREA5/
AREA6/AREA7/AREA8/FULL]
07/01/05 00:00:01
CAM1
CAM
CAM
M CAM
CAM5
CAM6
CAM7
CAM8
5-7) TIMER RECORD MODE
• TIMER : Set this option to ON to setup Timer
Recording [ON/OFF].
• DAY : Select the day of a week for the timer recording
[MON, TUE, WED, THU, FRI, SAT, DAILY, SUN].
• START & END : Set the starting and ending time for
the timer recording [00:00 ~ :59].
• FIELD RATE : Set the number of fields to be
recorded per second [NTSC][1/.5/.75/7.5 IPS]
[PAL][0.8/1.6/.1/6. IPS].
• Use
,
,
,
key to make change.
Caution
There are three types of recording modes: Event Re
-
cording (Motion Detection & Alarm), Timer Recording,
and Normal Recording.
If all three recording modes are selected at the same
time, recording takes place in the order of Event,
Timer, and Normal.
Содержание SMT-190DK
