background image

42

DP OUT

Select the input signal to output to the next monitor and the output mode to simplify the connection 
and control of displaying devices.

 

If the 

MST

 mode is selected for 

DP OUT

FreeSync

 is not supported for all connected monitors.

 

Before selecting the 

MST

 mode for 

DP OUT

, make sure that the device supports 

DisplayPort:MST

 (Daisy 

Chain)/HBR2 (High Bit Rate). Incorrect settings may lead to black screen or inconsistency between the 
actual output mode and the selected output mode. If a black screen occurs, change the 

DP OUT

 output 

mode.

 

MST/SST

: A technology used for connection and driving of multi-stream display signals.

 

MST

: Stands for Multi-Stream Transport. Can transport multiple video and audio streams, but 

needs the support of both the drive capacity of the graphics card and the resolution of the 
monitor.

 

SST

: Stands for Single Stream Transport. Can transport only a combination of a single video 

stream and a single audio stream.

 

DP OUT mode: 5 modes

USB Type-C:MST
USB Type-C:SST
DisplayPort:MST
DisplayPort:SST
HDMI:SST

DP OUT (MST/SST) Function Implementation

Connecting a PC via DisplayPort

MST

DP IN

DP IN

DP OUT

SST

DP IN

DP IN

DP OUT

 

Make sure that the graphics card supports the MST (Daisy Chain) function. To check this, visit the 
website of the graphics card manufacturer.

 

The output mode of 

DP OUT

 varies with the settings of DisplayPort Ver. When 

DisplayPort Ver.

 is 

set to 

1.1

DP OUT

 only supports 

SST

.

 

When connecting a PC using DP cable, you must set DP OUT mode to "DisplayPort: MST (SST)" on 
the OSD menu. (OSD – 

System

 – 

DP OUT

 - 

DisplayPort:MST

/

DisplayPort:SST

)

 

Because of the bandwidth limit of DisplayPort Ver. 1.2, up to two 2560 x 1440 @ 60 Hz monitors 
can be connected and used. But this specification may vary depending on the cable used and the 
performance of the graphics card.

PC

Monitor 1

Monitor 2

OSD → 

DisplayPort:SST

Screen A

Screen A

PC

Monitor 1

Monitor 2

OSD → 

DisplayPort:MST

Screen A

Screen B

DP Cable

DP Cable

DP Cable

DP Cable

Содержание S24H851QF Series

























































Отзывы: