Samsung RS277ACPN Скачать руководство пользователя страница 65

Страница: 65 / 93

4-6. Load Operation Check Function

1) In the normal operation, press Power Freeze and Power

Cool buttons simultaneously for 6 seconds, then the display

panel will blink for 2 seconds.

2) Press Fridge Temp. button to get into this check mode

ⓐ

with an audible tone.

3) Each illuminating LED segment stands for the component

which has an output signal from the control board.

4) This mode will terminate automatically after 30 seconds.

Troubleshooting and major adjustment



Press both buttons simultaneously for 6

seconds, all LED lights will be turned off. At

this time press button

ⓐ

※

For the REFRIGERATOR FAN, only one rpm is applied for the

current models, so that ☜ and ☜ show REFRIGERATOR FAN

operation only.

※

The FREEZER FAN and CONDENSER FAN are operated to High/Low

rpm automatically according to the operational condition.

※

☜☜ and ☜ only explain the system operation state according to the

ambient condition

Contents

①

REFRIGERATOR FAN High or AC
motor operation

②

REFRIGERATOR FAN Low

③

REFRIGERATOR DEFROST heater

④

Start mode

⑤

Overload mode

⑥

Low-temperature mode

⑦

Exhibition mode

⑧

COMPRESSOR

⑨

FREEZER FAN High

⑩

FREEZER FAN Low

⑪

FREEZER DEFROST Heater

⑫

CONDENSER FAN High

⑬

CONDENSER FAN Low

⑭

Dispenser-Heater

⑮

Damper

Normal condition



Table of Load Mode Check List

Содержание RS277ACPN






























































































Результаты поиска

Содержание RS277ACPN

Отзывы:

Похожие инструкции для RS277ACPN

Бренды по названию

Популярные бренды

Samsung RS277ACPN, Руководство пользователя

Результаты поиска

Содержание RS277ACPN

Отзывы:

Похожие инструкции для RS277ACPN

Бренды по названию

Популярные бренды