Samsung RF4287HABP Скачать руководство пользователя | Manualshive

Страница: 79 / 132

background image

80

TROUBLESHOOTING

- The refrigerator of this model has BLDC FAN motor. BLDC motor is driven by DC 7~12V.
- On the normal condition of COMP ON, it operates together with F-FAN motor.

If door is opened and closed once at a high ambient temperature, it will be operated after 1 minute
delay.
Therefore, you are advised not to taken it for an error.

-. If there is a trouble, you should select the self-diagnostic function to check the trouble before power off.

4-2-2. If FAN does not operate

Start

Is COMPRESSOR ON ?

Door & MICOM State

Door

F FAN pulse voltage

CN76#7(Brown)

The voltage measured around 2~3V
with multi-meter though the voltage is
very weak because of pulse signal

☞

Display for checking the self-diagnostic function

Typical PCB Ground

REG1 Heater Sink

F

MICOM

(#83)

Close
Open

5V(High)

0V(Low)

0V(Low)

5V(High)

R MICOM(#82)

Right and Left

Execute manual

operation

FAN work normally

Repair the connection

of Door switch

Replace MAIN PCB

1) F-FAN

Typical PCB Ground
REG1 Heater Sink

Power ON with 5 minutes
delay after power OFF.
For preventing the over
load of compressor)

◆

Expected causes

①

Check that if FAN-MOTOR has failure

itself.

②

Check that if wiring connection has bad

contact.

③

Check the input of the fan motor rotation

pulse when motor fan operates.

CN76-7(F),8(R),9(C)will generate the pulse signal when motor rotates.
These signals will be inputted into MICOM.
Unless signals are not inputted during motor operating, will be ON 10
seconds after fan Off. But if signals are not still entered, the above
operation will restart four times more.
If signals are not entered continuously, the motor will be restarted after
10 Minutes. This function is effective when the normal operation of motor
would be restrained by foreign matters such as ice.

☞

Checking method of R,F,C FAN Motor voltage

The voltage between PCB typical Ground REG1 Heater Sink and
F FAN ; CN76#3(Yellow) shall be less than DC 7~12V.
R FAN ; CN76#4(Orange) shall be less than DC 7~12V.
C FAN ; CN76#5(Sky-blue) shall be less than DC 7~12V.
- Recheck if resistance values are different after measuring.

Is the voltage between MAIN

PCB REG1 Heater Sink and CN76#3

(Yellow) around DC7~12V?

Is the voltage between MAIN

PCB REG1,Heater Sink and CN76#4

(Orange) around DC7~12V?

Is the voltage between MAIN

PCB REG1, HEAT SINK and CN

76#5(Sky -blue) around DC7~12V?

Is the external temperature

above 66.2

℉

(19

℃

)?

Recheck after 5 minutes
(Time could be delayed
depending on the
temperatures. If the
temperature is lower, It
may not operate : about
59

℉

(below 15

℃

)

Is the voltage between MAIN

PCB REG1,Heater Sink and CN

30#2 (Purple) around 0V?

Is the voltage between MAIN

PCB REG1 Heater Sink and CN30#1

(Black) around 4.5~5V?

Does DC7~12V alternate with

below DC 2V between MAIN PCB REG1

Heater Sink and CN76 #3(Yellow)

Does DC7~12V alternate with below

DC 2V between MAIN PCB REG1 Heater

Sink and CN76#4(Orange)

Does DC7~12V alternate with below

DC 2V between MAIN PCB REG1 Heater

Sink and CN76#5(Sky-blue)

In initial power to appliance, the compressor
and fans of fresh food/ freezer, compressor
fan operate. If freezer temperature is sensed
of 41

℉

by momentary power failure, fans

will operate after 5 minutes.

Reference

2) R-FAN

3) C-FAN

R FAN ERROR

F FAN ERROR

C FAN ERROR

AW3 SM-EN 2011.3.31 2:56 PM 페이지80 in

«
...
77
78
79
80
81
...
»

Содержание RF4287HABP





































































































































Отзывы:

Нет отзывов

Похожие инструкции для RF4287HABP

Бренд: Master Bilt Страницы: 2

Бренд: Smeg Страницы: 12

Бренд: AYA Страницы: 41

Бренд: Hanseatic Страницы: 56

Бренд: IKEA Страницы: 36

Бренд: Admiral Страницы: 6

Бренд: Guzzanti Страницы: 91

Бренд: THOMSON Страницы: 85

Бренд: CDA Страницы: 20

Бренд: Indesit Страницы: 16

Бренд: YATO Страницы: 92

Бренд: DAEWOO ELECTRONICS Страницы: 83

Бренд: Chandler Страницы: 12

Бренд: Zanussi Страницы: 20

Бренд: AEG Страницы: 20

Бренд: Hitachi Страницы: 32

Бренд: Hitachi Страницы: 24

Бренд: Hitachi Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды