background image

E-

4

Getting Started

You have just purchased a multi function wired remote controller and it has 

been installed by your installation specialist.

Your User’s Manual contain much valuable information on using  

your multi function wired remote controller. Please take the time to read 

them as they will help you take full advantage of the unit’s features.

In the manual, you will find a series of step-by-step procedures for each 

function available.

The illustrations in the step-by-step procedures use 3 different symbols:

PRESS

PUSH

HOLD DOWN

Multi Function Wired Remote Controller

The multi function wired remote controller is installed on the wall.

Schedule number/

Schedule applied 

unit display

Schedule/ 

Current time  

display 

Operation mode 

display

AC fan speed/ 

air swing display

Special function 

display

ERV fan speed 

display

7-day schedule setup

Mode selection

ERV on/fan speed 

control

Swing button

Energy saving  

function selection

Room temperature 

check button

Schedule reset button

Temperature 

display

Operation ON/OFF button

Temperature setting 

button

Fan speed setting 

button

Note

   

The 

 

button operates only when 1 indoor unit and 1 ERV unit is 

connected to the multi function wired remote controller. If ERV unit is 

not connected or more than 2 ERV units are connected, 

 will be 

displayed when you control it.

   

ERV operates in Heat Exchange mode only.

   

Press the 

 buttons after cleaning the air filter. 

 sign will be off. 

The remote controller will display the filter sign to alert the user to clean the 

filter and turn off the display when the 

 

buttons are pressed.

   

 will be displayed if you press the button of the function that the 

indoor unit does not support.

   

If you press 

 button when ERV unit is connected to the multi function 

wired remote controller, you can turn on/off both of ERV unit and the air 

conditioner at the same time or turn on/off the air conditioner only.  

The default setting is turning on/off both of them.  

(Refer to the installation manual.)

   

Even if the ERV and air conditioner are set to turn on/off at the same time, 

you can control the air conditioner and ERV individually by other controllers 

(Wireless remote controller, Centralized controller, S-NET mini, etc.) except 

the multi function wired remote controller.

MWR-WE00_IB_E_30794-1.indd   4

2009-06-22   ソタネト 2:36:41

Содержание MWR-WE00





























Отзывы: