Samsung MT3204 Series Скачать руководство пользователя

Страница: 15 / 122

Confidential

Preface

MT3204 Series Installation Manual v1.0

Equipment Markings

This marking on the product, accessories or literature indicates that the

product and its electronic accessories (e.g. charger, headset, USB cable)

should not be disposed of with other household waste at the end of their

working life. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, please separate these items

from other types of waste and recycle them responsibly to promote the

sustainable reuse of material resources.
Household users should contact either the retailer where they purchased

this product, or their local government office, for details of where and how

they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and

conditions of the purchase contract. This product and its electronic

accessories should not be mixed with other commercial wastes for

disposal.

Correct disposal of batteries in this product

(Applicable in countries with separate collection systems.)

The marking on the battery, manual or packaging indicates that the

battery in this product should not be disposed of with other household

waste. Where marked, the chemical symbols Hg, Cd or Pb indicate that

the battery contains mercury, cadmium or lead above the reference levels

in EC Directive 2006/66.
The battery incorporated in this product is not user replaceable. For

information on its replacement, please contact your service provider. Do

not attempt to remove the battery or dispose it in a fire. Do not

disassemble, crush, or puncture the battery. If you intend to discard the

product, the waste collection site will take the appropriate measures for

the recycling and treatment of the product, including the battery.

Hot surface warning

Allow to cool before servicing.
Do not touch before cooling.
Notice! Be careful not to touch due to high temperature.
The system must be installed in a restricted area, and make sure the

work is done by personnel properly trained for the job.

Protective earth

MMU should be grounded.

Содержание MT3204 Series























































































































Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды

Samsung MT3204 Series, Руководство по установке

Результаты поиска

Содержание MT3204 Series

Отзывы:

Похожие инструкции для MT3204 Series

Бренды по названию

Популярные бренды