Samsung ML-1610 Series Скачать руководство пользователя страница 63

Страница: 63 / 131

Samsung Electronics

Service Manual

Disassembly and Reassembly

5-2

5.2 Disassembly and Reassembly

5.2.1 Front Cover

1.Open the front cover.(The front cover and the cas-

sette tray are assembled with the same assembly.)

2.Separate the cover from the lock of the frame by

pulling the right bottom of the cover toward the arrow
direction. Pull out the front cover to the left as shown
as below.

1.For separating only cassette tray,open the tray.

2.Hold the set and lift up the hook on the left bottom

toward the arrow direction.Separate the cassette tray
by pulling it out to the left as shown as below.

Front Cover

Cassette Tray

5.2.2 Cassette Tray

Содержание ML-1610 Series




































































































































Результаты поиска

Содержание ML-1610 Series

Отзывы:

Похожие инструкции для ML-1610 Series

Бренды по названию

Популярные бренды

Samsung ML-1610 Series, Руководство по обслуживанию

Результаты поиска

Содержание ML-1610 Series

Отзывы:

Похожие инструкции для ML-1610 Series

Бренды по названию

Популярные бренды