manualshive.com logo in svg

Samsung ML-1610 Series, Руководство по обслуживанию

Поделиться
Скачать
Samsung ML-1610 Series Скачать руководство пользователя страница 13

Product Specifications

Samsung Electronics

Service Manual

2-5

2.3  Model Comparison Table

Model Name

ML-1610

ML-1615P

ML-1750

General

Company

Samsung

Samsung

Samsung

Printing Process
Print Method:

Electrophotographic Laser

Electrophotographic Laser

Electrophotographic laser

Print Speed

Up to 16ppm in A4, Up to 17ppm in letter

Up to 16ppm in A4, Up to 17ppm in letter

Up to 16ppm(A4) (ML-1510 : 14ppm)

FPOT

10sec

10sec

12sec

Resolusion

600*600

600*600

600*600

Duty Cycle, Monthly

up to 5000 prints per month

up to 5000 prints per month

up to 15,000 prints per month

Hardware Software
Processor Type

Samsung 150MHz

Samsung 150MHz

66MHz RISC(Jupiter3)

Memory

2MB(2MB)

8MB SDRAM(8MB)

8MB SDRAM(2MB)

OS

Win9X/ME/2000/XP/Linux7/Mac OS8.6

Win9X/ME/2000/XP/Linux7/Mac OS8.6

Win9X/ME/2000/XP/Linux7/Mac OS8.6

Standard Emulations

SPL

SPL

GDI(SPL)

Interface Support
Standard Interfaces

USB 1.1(Compatible with USB 2.0)

USB 1.1

USB 1.1

Cable Not Supply(KOR,CHINA is Supply)

IEEE 1284 Parallel

Cable Not Supply

Optional Interfaces

N/A

N/A

N/A

Paper Handling
Standard Paper Input

150 Sheets Multi-purpose Tray 

150 Sheets Multi-purpose Tray 

250 Sheets Multi-Purpose Cassette,

Single Sheets Adjustable Manual Feed

Paper Output

Face down : 50 Sheet(TBD)

Face down : 50 Sheet(TBD)

50 Sheet Face Down Tray

Duplexing

Manual

Manual

Paper Weight :

- Plain paper

16 to 24 lb. Bond(60 to 90g/m2)

16 to 24 lb. Bond(60 to 90g/m2)

16 to 24 lb. Bond(60 to 90g/m2)

- Thick stock

24 - 90 lb. Index(163g/m2)

24 - 90 lb. Index(163g/m2)

24 - 90 lb. Index(163g/m2)

Physical
Type

Laser Printer with Internal Controller

Laser Printer with Internal Controller

Laser Printer with Internal Controller

Dimensions w/output 

358mm x 299mm x 217mm

358mm x 299mm x 217mm

352mm x 372mm x 196mm

tray extended(WxDxH)
Weight(without shipping)

5.75kg

5.5kg

7.05kg(manual book : 7kg)

Carton Dimensions

455mm x 415mm x 325mm

455mm x 415mm x 325mm

508mm x 425mm x 265mm

(WxDxH)
Weight(as shipped)

7.65kg

7.65kg

9kg

Electical
Power Requirements
Power Consumption 

Power Consumption

Power Consumption

Power Consumption

300W printing, 10W Down Sleep Mode

300W printing, 10W Down Sleep Mode

330W printing, 10W Down Sleep Mode

Energy Star* Compliant

Yes

Yes

Yes

Environmental
Temprature :

- Operating

10

to 32

10

to 32

10

to 32

- Non-Operating

0

to 40

0

to 40

0

to 40

Humidity :

- Operating

: 20% to 80% RH

: 20% to 80% RH

: 20% to 80% RH

- Non-Operating

: 20% to 80% RH

: 20% to 80% RH

: 20% to 80% RH

Noise Level :
Operating 

Operating : <50dB(A), Standby :<35 dB(A)

Operating : <50dB(A), Standby :<35 dB(A)

Operating : <52dB(A), Standby :<35 dB(A)

Consumables
Starter 

up to 1,000 pages(A4/Letter) at ISO 5% coverage

up to 1,000 pages(A4/Letter) at ISO 5% coverage

up to 1,000 pages(A4/Letter) at ISO 5% coverage

continuous printing.

continuous printing.

continuous printing.

Replacement up 

to 

2,000 pages(A4/Letter) at ISO 5% coverage

up to 2,000 pages(A4/Letter) at ISO 5% coverage   up to 3,000 pages(A4/Letter) at ISO 5% coverage

Содержание ML-1610 Series




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды