background image

14

Step-by-step installation guide

C.  OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

C1.  ADAPTING THE MICROWAVE BLOWER FOR 

OUTSIDE BACK EXHAUST

1

.  Remove and save screw that holds blower Plate to 

microwave.

Back of 

Microwave Oven

Blower 

Retaining 

Screws

2

.  Open the blower door by lifting it up at the back 

of the microwave. Remove and save the blower 

shield on the back of the microwave by sliding it up. 

Remove and save the metal vent fan cover on the 

back of the microwave by sliding it up.

3

.  Carefully pull out the blower unit. The wires will 

extend far enough to allow you to adjust the blower 

unit.

BEFORE: Fan Blade 

Openings Facing Forward

End B

End A

CAUTION: 

To avoid breaking or cracking the blower 

blade, do not touch the blade. Hold the outer case of the 

blower when you pull it out or put it back in place.

4

. Remove Parts “A” with tin snips or pliers.

Parts “A”

5

.  Rotate the blower unit counterclockwise 180 °.

Before Rotation

After Rotation

Back of Microwave

Back of Microwave

6

.  Place the blower unit back into the opening.

AFTER: Fan Blade 

Openings Facing Back

End B

End A

CAUTION: Do not pull or stretch the blower unit 

wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should 

match exhaust openings on the rear of microwave 

oven.
7

.  Close the blower door. Slide blower shield onto the 

top of the blower door opening. Secure the blower 

to the microwave oven using the blower retaining 

screws from Step 1 except the upper blower motor 

retaining screw.

Blower 

Retaining Screw

Blower Shield

Blower 

Retaining Screw

Back of 

Microwave Oven

8

.  Slide the exhaust adaptor onto the back of the 

microwave oven, securing it into the lower locking 

tabs. Take care to ensure that the damper hinge is 

installed so that it is at the top and that the damper 

swings freely. Reinstall the upper blower motor screw 

through the adaptor and the blower door and into 

the back of the microwave oven.

Guide

Guide

Adaptor

Locking Tabs 

(not shown)

Blower Motor Door 

Retaining Screw

Back of 

Microwave Oven

SMH1927_XAC_DE68-04108B-06_EN+CFR.indb   14

SMH1927_XAC_DE68-04108B-06_EN+CFR.indb   14

2022-01-20   �� 10:19:10

2022-01-20   �� 10:19:10

Содержание me18h704sfs



















Отзывы: