Samsung ME179KFETSR/AA Скачать руководство пользователя страница 16

16

Step-by-step installation guide

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More 

Than Wall Thickness

Mounting 

Plate

Spacing for Toggles More 

Than Wall Thickness

Bolt End

Mounting 

Plate

Toggle 

Bolt

Wall

Toggle Wings

3

.  Place the mounting plate against the wall and 

insert the toggle wings into the holes in the wall to 

mount the plate.

NOTE

: Before tightening the toggle bolts and wood 

screw, make sure the bottom of the Mounting plate 

runs along the bottom Horizontal line of the “Rear wall 

Template” and the Mounting plate is properly centered 

under the cabinet.

CAUTION

: Be careful to avoid pinching your fingers 

between the back of the mounting plate and the wall.

4

.  Tighten all bolts. Pull the plate away from the wall 

to help tighten the bolts. Tighten the screw.

C.  USE THE TOP CABINET 

TEMPLATE TO PREPARE 

THE TOP CABINET

You need to drill holes for the top support screws and 

a hole large enough for the power cord to fit through.

•  Read the instructions on the TOP CABINET 

TEMPLATE.

•  Tape it underneath the top cabinet.
•  Drill the holes, following the instructions on the 

TOP CABINET TEMPLATE.

CAUTION

: Wear safety goggles when drilling holes in 

the cabinet bottom.

D.  MOUNT THE MICROWAVE 

OVEN

FOR EASIER INSTALLATION AND PERSONAL 

SAFETY, WE RECOMMEND THAT TWO PEOPLE 

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use the handle 

during installation.

NOTE

: If your cabinet is metal, use the nylon 

grommet in the power cord hole to prevent the cord 

from being cut.

NOTE

: Filler blocks are required when mounting this 

unit under any cabinet with a recessed bottom or 

front overhang. (See page 9.)

IMPORTANT: The case damage that will occur 

from over tightening screws if you do not use 

filler blocks is not covered under warranty.

IMPORTANT: For models with the grease filter 

installed, don’t push up on the filter when you 

mount the oven.

NOTE

: When mounting the microwave oven, thread 

the power cord through hole in the bottom of the top 

cabinet. Keep it tight throughout Steps 1–3. Do not 

pinch the cord or lift the oven by pulling cord.

Grease Filter

Grease Filter

(Installation)ME179KFETSR_DE68-04129A_AA.indd   16

2012-05-21   �� 9:57:31

Содержание ME179KFETSR/AA





















Отзывы: