Samsung ME16K3000AS Скачать руководство пользователя страница 6

Страница: 6 / 24

General information

• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.

• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by

arrangement between customer and installer.

DAMAGE - SHIPMENT/INSTALLATION

HARDWARE PACKET

PART

QUANTITY

Template

INST

ALLA

TION

INSTR

UCTIONS

Wood Screws
(¼” x 2”)

Template

INST

ALLA

TION

INSTR

UCTIONS

Toggle Bolts
(and wing nuts)
(3/16” x 3”)

Template

INST

ALLA

TION

INSTR

UCTIONS

Self-aligning
Machine Screws
(¼”-28 x 3¼”)

Template

INST

ALLA

TION

INSTR

UCTIONS

You will find the installation hardware contained in a
packet with the unit. Check to make sure you have all
these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

PART

QUANTITY

4/0#!").%44%-0,!4%

2%!27!,,4%-0,!4%

Top Cabinet
Template

4/0#!").%44%-0,!4%

2%!27!,,4%-0,!4%

Rear Wall
Template

Template

INST

ALLA

TION

INSTR

UCTIONS

Installation
Instructions

Template

INST

ALLA

TION

INSTR

UCTIONS

Separately
Packed Grease
Filter

Template

INST

ALLA

TION

INSTR

UCTIONS

Exhaust adaptor

PARTS INCLUDED

DE68-03587B-EN.indd 6

2008-12-09 �� 4:13:02

Содержание ME16K3000AS

























Результаты поиска

Содержание ME16K3000AS

Отзывы:

Похожие инструкции для ME16K3000AS

Бренды по названию

Популярные бренды

Samsung ME16K3000AS, Руководство по установке

Результаты поиска

Содержание ME16K3000AS

Отзывы:

Похожие инструкции для ME16K3000AS

Бренды по названию

Популярные бренды