Samsung ME16K3000AS Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

background image

13

Step-by-step installation guide

A4. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during
installation.

NOTE: If your cabinet is metal, use the nylon grommet
around the power cord hole to prevent cutting of the
cord.

NOTE: We recommend using filler blocks if the cabinet
front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet. Keep
it tight throughout Steps 1-3. Do not pinch cord or lift
oven by pulling cord.

1

. Lift microwave,

tilt it forward, and
hook slots at back
bottom edge onto
four lower tabs of
mounting plate.

2

. Rotate front of oven

up against cabinet
bottom

3

. Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by turning
the screw at least two full turns after the threads
have engaged. (It will be completely tightened later.)
Be sure to keep power cord tight. Be careful not
to pinch the cord, especially when mounting
flush to bottom of cabinet.

A3. INSTALLATION PROCEDURE

FOR EXHAUST ADAPTOR AND
PROPER DAMPER OPERATION
CHECK

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the TOP

CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in
the cabinet bottom.

DE68-03587B-EN.indd 13

2008-12-09 �� 4:13:11

Exhaust Adaptor and Damper is

shipped assembled to the filler-upper.

«
...
11
12
13
14
15
...
»

Содержание ME16K3000AS

























Отзывы:

Нет отзывов

Похожие инструкции для ME16K3000AS

Бренд: Omega Страницы: 18

Бренд: Wanderer Страницы: 6

MC28H5145 Series

Бренд: Samsung Страницы: 80

Бренд: Hartmann Страницы: 16

Бренд: Quadro Страницы: 72

Бренд: GE Страницы: 32

Бренд: montpellier Страницы: 22

Бренд: baxter Страницы: 20

Бренд: Cleveland Страницы: 155

Бренд: John Lewis Страницы: 48

Бренд: Hoover Страницы: 110

Бренд: IAG Страницы: 26

Бренд: Sunbeam Страницы: 15

Бренд: Oster Страницы: 30

Бренд: iCES Страницы: 72

Бренд: Kenwood Страницы: 44

Бренд: Kenwood Страницы: 32

Бренд: Kenwood Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды