Samsung ME16A4021AB Скачать руководство пользователя страница 6

Страница: 6 / 20

General information

•

If the unit is damaged in shipment,

return the unit to the store in which it was bought for repair or

replacement.

•

If the unit is damaged by the customer,

repair or replacement is the responsibility of the customer.

•

If the unit is damaged by the installer

(if other than the customer), repair or replacement must be made by

arrangement between customer and installer.

DAMAGE – SHIPMENT/INSTALLATION

HARDWARE PACKET

PART

QUANTITY

Wood Screws

(¼˝ x 2˝)

Toggle Bolts

(and wing nuts)

(

˝ x 3˝)

Self-aligning

Machine Screws

(¼˝-28 x 3 ¼˝)

You will find the installation hardware contained in a

packet with the unit. Check to make sure you have all

these parts.

NOTE

: Some extra parts are included.

ADDITIONAL PARTS

PART

QUANTITY

TOP CABINET TEMPLATE

Top Cabinet

Template

REAR WALL TEMPLATE

Rear Wall Template

Installation

Instructions

Separately Packed

Grease Filters

Exhaust adaptor

PARTS INCLUDED

SMH8165_XAA_DE68-03587A-10_EN.indd 6

6/19/2019 3:44:26 PM

Содержание ME16A4021AB





















Результаты поиска

Содержание ME16A4021AB

Отзывы:

Похожие инструкции для ME16A4021AB

Бренды по названию

Популярные бренды

Samsung ME16A4021AB, Руководство по установке

Результаты поиска

Содержание ME16A4021AB

Отзывы:

Похожие инструкции для ME16A4021AB

Бренды по названию

Популярные бренды