36
GB
37
SAMSUNG strives to improve its products at all times. Both the design specifications and these user
instructions are thus subject to change without notice.
Technical Specifications
RADIO
LW
Tuning range 144 - 290 KHz
Usable sensitivity 60 dB
AM (MW)
Tuning range 522 - 1611 KHz
Signal/noise ratio
40 dB
Usable sensitivity
54 dB
Total harmonic distortion
2 %
FM
Tuning range 87.5 - 108 MHz
Signal/noise ratio
60 dB
Usable sensitivity
10 dB
Total harmonic distortion
0.5 %
COMPACT DISC PLAYER
Capacity 3
discs
Frequency range
20 Hz - 20 KHz (± 1 dB)
Signal/noise ratio
85 dB (at 1 KHz) with filter
Distortion
0.1 % (at 1 KHz)
Channel separation
70 dB
Disc sizes
Diameter: 120 or 80 mm. Thickness: 1.2 mm
TAPE DECK
Frequency range
125 Hz ~ 10 KHz
Signal/noise ratio
40 dB
Channel separation
35 dB
Erasing effect
60 dB
AMPLIFIER
front speakers
2 x 30 Watts RMS,IEC (total harmonic distortion: 10 %)
subwoofer speakers
2 x 60 Watts RMS,IEC (total harmonic distortion: 10 %)
center,rear(L,R) speakers
3 x 25 Watts RMS,IEC (total harmonic distortion: 10 %)
Channel separation
50 dB
Signal/noise ratio
75 dB
GENERAL
Dimensions
270 (W) x 332 (H) x 443 (D) mm
It always takes a little time to become familiar with a new appliance. If you have any of the problems listed below,
try the solutions given. They may save you the time and inconvenience of an unnecessary service call.
If the above guidelines do not allow you to solve the problem, take a note of:
The model and serial numbers, normally printed on the rear of the system
Your warranty details
A clear description of the problem
Then contact your local dealer or SAMSUNG after-sales service.
Before Contacting the After-Sales Service
PROBLEM
The system does not work
There is no sound
The Timer does not work
System still doesn’t work, even
after following steps above.
The compact disc player does
not start playing
The icon appears on
screen.
Disc Menu doesn’t appear.
Playback mode differs from
the Setup Menu selection
The screen ratio cannot be
changed.
The tape does not start play-
ing
The volume falls off
The cassette is not erased correctly
There is excessive wow and flutter
Reception is poor or no radio
stations are received at all
There’s no sound
The sound is distorted
G
E
N
E
R
A
L
C
D
/
D
V
D
R
A
D
I
O
S
U
B
W
O
O
F
E
R
P
S
W
1
0
0
E
O
N
L
Y
C
A
S
S
E
T
T
E
S
CHECKS/EXPLANATION
• The main lead is not correctly plugged into a wall socket or the wall socket is not switched on.
• The remote control batteries need replacing or the polarity has not been respected.
• The On/Standby button has not been pressed.
• The volume has been completely turned down.
• The correct function (TUNER, CD, TAPE, AUX) has not been selected.
• You have connected a set of earphones.
• The loudspeaker wires have been disconnected.
• The Mute button has been pressed.
• The timer has been stopped by pressing Timer On/Off.
• Press the S. Bass button for 5 seconds in power ‘OFF’(standby), the system is returned the
original position (RESET)
• The CD function has not been selected.
• The disc has been inserted face down or is either dirty or scratched.
• The laser sensor is dirty or dusty.
• The system has not been installed on a flat, horizontal surface.
• Condensation has formed in the player; leave the system in a warm, airy room for at least one hour.
• This player cannot play CD-ROMs, DVD-ROMs, CD-R, etc. Insert a DVD, a VIDEO-CD or a CD.
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
• Check if the disc has a Menu.
• Some of the functions selected in the Setup Menu may not work properly if the disc is not
encoded with the corresponding function.
• The Screen Ratio is fixed on your DVDs.
• The TAPE function has not been selected.
• The cassette has not been inserted correctly.
• The cassette player has not been closed.
• The tape is either slack or broken.
• The audio heads are dirty.
• The rollers or drive capstans are dirty.
• The tape is worn.
• The TUNER function has not been selected.
• The radio frequency has not been correctly selected.
• The aerial has been disconnected or is not facing the right way. Turn it until you find the best
orientation.
• You are in a building that blocks radio waves; you must use an outside aerial.
• Check that this subwoofer and components are connected correctly and securely.
• Rotate Volume clockwise to turn the Volume up.
• If the input signal is imperfect or distorted.
• If the input signal level is too high.
(
(
