Samsung MagicLAN SWL-2000N Скачать руководство пользователя

Страница: 2 / 77

Notice 1

This manual cannot be reproduced in any form without the prior written permission of

SAMSUNG Electro-Mechanics, Co., Ltd.

SAMSUNG Electro-Mechanics, Co., Ltd. reserves the right to change this manual and the

specifications to improve products without prior notice. So you can get the most recent

software and user documentation for all MagicLAN products on our web site.

•

MagicLAN is the trademark of SAMSUNG wireless LAN.

•

MS-DOS, Microsoft and Windows are registered trademarks of Microsoft Corporation.

All other brand and product names are trademarks of registered trademarks of their

respective holders.

http://www.MagicLAN.com

Service Dept.

+82-331-210-6805

Sales Dept. +82-331-210-6386

SAMSUNG – America Corporation

Western US Marketing Office

85 Tasman Drive

San Jose, CA 95134 USA

Tel: (408)544-5200 Fax: (408)544-4967

Eastern US Marketing Office

LanPAL AKOM Corporation

9 Parklawn Dr.

Bethel, CT 06801

Tel: (203)778-9500 Fax: (203)778-9525



1999 SAMSUNG Electro-Mechanics, Co., Ltd.

Содержание MagicLAN SWL-2000N














































































Результаты поиска

Содержание MagicLAN SWL-2000N

Отзывы:

Похожие инструкции для MagicLAN SWL-2000N

Бренды по названию

Популярные бренды

Samsung MagicLAN SWL-2000N, Руководство пользователя

Результаты поиска

Содержание MagicLAN SWL-2000N

Отзывы:

Похожие инструкции для MagicLAN SWL-2000N

Бренды по названию

Популярные бренды