background image

17. When checking the continuity of the witches

or transformer, always make sure that the
power is OFF, and one of the lead wires is
disconnected.  

18. Components that are critical for safety are

indicated in the circuit diagram by
shading,    

or      .  

19. Use replacement components that have the

same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards. 

1. High Voltage Warning

Do not attempt to measureany of the high
voltages--this includes the filament voltage
of the magnetron. High voltage is present
during any cook cycle.  

Before touching any components or wiring,
always unplug the oven and discharge the
high voltage capacitor (See Figure  1-1)

2. The high-voltage capacitor remains charged

about 30 seconds after disconnection.  Short
the negative terminal of the high-voltage
capacitor to to the oven chassis.  (Use a
screwdriver.)

3. High voltage is maintained within specified

limits by close-tolerance, safety-related
components and adjustments.  If the high
voltage exceeds the specified limits, check
each of the special components. 

1-2

Pretaution

Samsung Electronics

1-2 Special Servicing  Precautions (Continued)

1-3  Special High Voltage Precautions

Fig. 1-1.  Discharging the High Voltage Capacitor

PRECAUTION

Never touch any circuit wiring with your hand nor with
uninsulated tool during operation.

H. V. Diode

Short

H. V. Capacitor

Touch chassis ground first then short to the high
voltage capacitor terminal by using screwdriver or
jumper wire.

PRECAUTION

There exists HIGH VOLTAGE ELECTRICITY with high
current capabilities in the circuits of the HIGH VOLTAGE
TRANSFORMER secondary and filament terminals. It is
extremely dangerous to work on or near these circuits
with the oven energized.
DO NOT measure the voltage in the high voltage circuit
including filament voltage of magnetron.

PRECAUTION

Servicemen should remove their watches whenever
working close to or replacing the magnetron.

Содержание G639C























Отзывы: