Samsung DW60A6080 Series страница 29 Скачать руководство пользователя

Страница: 29 / 32

Disassembly and Reassembly _ 29

2-12. RAIL BASKET / HOLDER RAIL REAR

- Rail Basket : DD81-02766A, DD81-02767A / SVC-RAIL MID-LEFT, RIGHT

DD81-02958A, DD81-02959A / SVC-RAIL 3RD-LEFT, RIGHT (DW60A609*)

- Holder Rail Rear : DD81-02768A / SVC-HOLDER-RAIL MIDDLE REAR

DD81-02960A / SVC-HOLDER-RAIL 3RD REAR (DW60A609*)

Part

Figure

Description

RAIL BASKET /

HOLDER RAIL

REAR

Holder Rail Rear

[DISASSEMBLY]

1. Remove the HOLDER RAIL REAR by pulling back

with releasing the hook.

Rail Basket Left

Rail Basket Right

2. Remove the RAIL BASKET.

Warning

Do not do this work without safety gloves. It may

cause injury from sharp edges.

[ASSEMBLY]

1. Fit the RAIL BASKET on the ROLLER RAIL.

Warning

Do not do this work without safety gloves. It may

cause injury from sharp edges.

Caution

Make sure of the direction of the RAIL BASKET

when it’s reassembled. The front part of the RAIL

BASKET faces upward.

2. Assemble the HOLDER RAIL REAR to the RAIL

BASKET.

Caution

Make sure to lock the hook to hole of RAIL

BASKET.

Содержание DW60A6080 Series

































Результаты поиска

Содержание DW60A6080 Series

Отзывы:

Похожие инструкции для DW60A6080 Series

Бренды по названию

Популярные бренды

Samsung DW60A6080 Series, Руководство по ремонту

Результаты поиска

Содержание DW60A6080 Series

Отзывы:

Похожие инструкции для DW60A6080 Series

Бренды по названию

Популярные бренды