DSR 9500A FT
A, CI, EM VIA, VIA CI
GB-4
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
DSR 9500A FT
A, CI, EM VIA, VIA CI
GB
GB-5
CONNECTING YOUR "DSR 9500A"
7. INSERTING SMARTCARDS FOR VIACCESS SERVICES
In order to view a scrambled service, you need to have the appropriate
conditional Access Module and a valid Smartcard. This DSR 9500A has the
Viaccess CAS embedded to view Viaccess programmes.
N
No
otte
e
: Insert the Smartcard with the gold coloured chip facing downwards.
8. INSERTING COMMON INTERFACE CAM AND SMARTCARD
(For models DSR 9500A CI, DSR 9500A VIA CI)
The DSR 9500A supports Common Interface CAMs under DVB specification.
The CI CAMs include a built-in smart card reader.
●
Insert the smart card into the CAM gently with the gold colored chip upwards
●
Slide in the CAM gently inside the slot so that it sits in the socket tightly.
●
Close the door.
●
To remove the CAM push the button provided by the side of the CAM slot.
The CAM will be ejected from the socket.
N
No
otte
e
: The following Common Interface CAMs are available now:
IRDETO, CONAX, CRYPTOWORKS, VIACCESS, NAGRAVISION,
SECA, Etc.
1. LOCATION OF THE RECEIVER
Your DSR 9500A should be placed under proper ventilation.
Don’t put in completely enclosed cabinet that will restrict the flow of air,
resulting in overheating.
The location should be safeguarded from direct sunlight,
excess moisture, rough handling or household pets.
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your
antenna system.
2. CONNECTING THE RECEIVER WITH DISH SYSTEM
After installing your antenna system, connect the coaxial cable from the
LNB of your antenna to "LNB" terminal marked at the rear
of the DSR 9500A.
All cable connectors should be finger tightened; do not use any kind
of wrench while tightenning connectors. The cable should be 75ohm
impedance coaxial twisted at the end with an "F" type connector.
3. CONNECTING THE RECEIVER TO TV
To connect the receiver with your television, you can use three methods;
via Scart Cable, RF cable, or RCA cable.
Connect the RF cable to the terminal marked "TV" at the rear panel
of DSR 9500A and its other end to the TV RF input socket.
In the case of connecting your TV through SCART cable, connect the
SCART connector marked TV to the respective SCART port on the TV.
4. CONNECTING YOUR ANALOG RECEIVER
To facilitate the user using analog receiver to view analog channels,
DSR 9500A has been provided with a loop through terminal marked as "LOOP".
Connect the coaxial cable from this terminal to the IF input terminal of
your analog receiver. Now by keeping the DSR 9500A in standby,
you will be able to tune and view analog channels from
your analog receiver.
5. CONNECTING YOUR VCR
To connect a VCR or DVD player, the DSR 9500A has been provided with SCART
at the rear marked "AV2".
Using a SCART connector, the VCR or DVD player can be connected to the receiver.
N
No
otte
e
: This is supported by standby.
6. CONNECTING EXTERNAL AUDIO / HI-FI SYSTEM
To connect any external Audio Hi-Fi system, the receiver has been provided
with two RCA connectors at the back of the receiver,
marked with AUDIO L and R respectively to connect the left and right Audio.
Connecting Figure
CONNECTING YOUR "DSR 9500A"
DSR 9500A_GB_10.12 11/23/02 9:33 AM Page 4
Содержание DSB-9500AV
