Samsung DC68-02312A-04 Скачать руководство пользователя

Страница: 11 / 36

SAMSUNG

Dryer Owner’s Instructions

A-5

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES,

WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES),

OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with

LP (liquid propane) gas, it must be converted for safe and proper performance by a qualiﬁed service

technician.
A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-oﬀ

valve be installed within 6’ of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the ﬂoor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.
Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT

reuse old ﬂexible metal gas lines. Flexible gas lines must be design certiﬁed by the American

Gas Association (CGA in Canada).

NOTE :

•

Any pipe joint compound used must be resistant to the action of any liqueﬁed petroleum gas.

•

As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION –

Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas ﬁtter. A “T” handle manual gas valve must be

installed in the gas supply line to your dryer. If a ﬂexible gas connector is used to install your dryer, the

connector must have a maximum length of 3’ (36”).

WARNING –

Gas leaks may occur in your system, creating a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with manufacturer’s instructions.

Installation Instructions

Содержание DC68-02312A-04





































Результаты поиска

Содержание DC68-02312A-04

Отзывы:

Похожие инструкции для DC68-02312A-04

Бренды по названию

Популярные бренды

Samsung DC68-02312A-04, Руководство пользователя

Результаты поиска

Содержание DC68-02312A-04

Отзывы:

Похожие инструкции для DC68-02312A-04

Бренды по названию

Популярные бренды