Samsung AM TXMDCH Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 52

background image

10

Installation location

Moving the Outdoor Unit

X

Select the moving route in advance.

X

Be sure that moving route is safe from the weight of the outdoor unit.

X

Do not slant the product more than 30˚ when carrying it. (Do not lay the product down sideways.)

X

The surface of the heat exchanger is sharp. Be careful not to get injured while moving and installing.

When moving with a crane or wire rope

X

When moving an outdoor unit to a higher place such as the rooftop.

- Fasten the wire rope as seen in the picture.

- Move the outdoor unit with the product packed to prevent possible product

damage during the transportation.

Wire rope/straps

Wood palette

When moving an outdoor unit with hands

X

Moving the outdoor unit by lifting up and carrying due to the short travel distance.

- Two people should carry the outdoor unit by holding transportation handle.

- Be careful not to damage the heat exchanger of the rear side of the outdoor unit during

transportation.

- Be careful not to get hurt by the sharp surface of the heat exchanger.

Installation and base ground work for an outdoor unit

X

Install the outdoor unit 150mm (6 inch) higher than the base ground and install the drain hole to connect the pipe to the
drainage.

X

When the front fan of an outdoor unit is installed in a place where the average snowfall is more than 150mm (6inch), the
discharge duct should be attached to the outdoor unit.

X

The concrete foundation should be 1.5 times larger than bottom of the outdoor unit.

X

It is necessary to install wire mesh or steel bar when outdoor units are installed on a soft foundation.

X

When installing multiple outdoor units at the same place, install the
H beam on the base ground.
(When installing a number of outdoor units, you can install it on the
base ground.)

X

Install the H beam [150mm (6 inch) x 150mm (6 inch) x t10 : basic
speciﬁcation] or vibration absorption frame to jut out from the base
ground.

X

After installing the H beam, apply corrosion protection.

X

Install a square pad [t=20mm (1 inch) or more] to prevent vibration
from the outdoor unit onto the base ground. Place the outdoor unit
on the H beam and ﬁx it with the bolt, nut and washer. (Fix with M10
basic anchor bolt, nut and washer.)

Outdoor unit

Anchor bolt

Nut, Spring
washer

H beam

Square pad

A+10~20mm
(0.5~1 inch) or more

A

20mm

(1 inch)

75mm

(3 inch)

or more

ki]_TW__]_hTWXptk}tGzGljvG䖐㨴㥐㛨ὤhhluUGGGXW

YWYWTWZTY^GGG㝘䟸GYaX[aY_

«
...
8
9
10
11
12
...
»

Содержание AM TXMDCH Series





















































Отзывы:

Нет отзывов

Похожие инструкции для AM TXMDCH Series

Бренд: NANO Страницы: 28

Бренд: Panasonic Страницы: 12

Бренд: Daikin Страницы: 61

Бренд: Daikin Страницы: 5

Бренд: Daikin Страницы: 23

Бренд: Daikin Страницы: 20

Altherma EABH16DA6V

Бренд: Daikin Страницы: 16

Бренд: Haier Страницы: 26

Бренд: Haier Страницы: 22

Бренд: Airwell Страницы: 55

Бренд: O3ZY Страницы: 15

Бренд: Carrier Страницы: 104

Бренд: DCG Страницы: 18

Softaire RERV-80

Бренд: Air Specialties Страницы: 16

Бренд: York Страницы: 30

Бренд: Danby Страницы: 80

Бренд: Carrier Страницы: 54

EML2M14S912IST3W

Бренд: Emelson Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды