background image

3

English

Saf
ety
 Inf
ormation

Carefully follow the precautions listed below because they are 

essential to guarantee the safety of the equipment.

  WARNING

 • Always disconnect the air conditioner from the power 

supply before servicing it or accessing its internal 

components.

 • Verify that installation and testing operations are 

performed by qualified personnel.

 • Verify that the air conditioner is not installed in an 

easily accessible area. 

General information

 • Carefully read the content of this manual before 

installing the air conditioner and store the manual in a 

safe place in order to be able to use it as reference after 

installation. 

 • For maximum safety, installers should always carefully 

read the following warnings. 

 • Store the operation and installation manual in a safe 

location and remember to hand it over to the new 

owner if the air conditioner is sold or transferred. 

 • This manual explains how to install an indoor unit with 

a split system with two SAMSUNG units. The use of 

other types of units with different control systems may 

damage the units and invalidate the warranty. The 

manufacturer shall not be responsible for damages 

arising from the use of non compliant units. 

 • The manufacturer shall not be responsible for damage 

originating from unauthorized changes or the improper 

connection of electric and hydraulic lines. Failure to 

comply with these instructions or to comply with the 

requirements set forth in the “Operating limits” table, 

included in the manual, shall immediately invalidate 

the warranty.

 • The air conditioner should be used only for the 

applications for which it has been designed: the indoor 

unit is not suitable to be installed in areas used for 

laundry. 

 • Do not use the units if damaged. If problems occur, 

switch the unit off and disconnect it from the power 

supply.

 • In order to prevent electric shocks, fires or injuries, 

always stop the unit, disable the protection switch 

and contact SAMSUNG’s technical support if the unit 

produces smoke, if the power cable is hot or damaged 

or if the unit is very noisy. 

 • Always remember to inspect the unit, electric 

connections, refrigerant tubes and protections 

regularly. These operations should be performed by 

qualified personnel only. 

 • The unit contains moving parts, which should always be 

kept out of the reach of children. 

 • Do not attempt to repair, move, alter or reinstall the 

unit. If performed by unauthorized personnel, these 

operations may cause electric shocks or fires.

 • Do not place containers with liquids or other objects 

on the unit. 

 • All the materials used for the manufacture and 

packaging of the air conditioner are recyclable. 

 • The packing material and exhaust batteries of the 

remote control (optional) must be disposed of in 

accordance with current laws.

 • The air conditioner contains a refrigerant that has to be 

disposed of as special waste. At the end of its life cycle, 

the air conditioner must be disposed of in authorized 

centers or returned to the retailer so that it can be 

disposed of correctly and safely.

Installing the unit

 • IMPORTANT: When installing the unit, always 

remember to connect first the refrigerant tubes, then 

the electrical lines. Always disassemble the electric 

lines before the refrigerant tubes. 

 • Upon receipt, inspect the product to verify that it has 

not been damaged during transport. If the product 

appears damaged, DO NOT INSTALL it and immediately 

report the damage to the carrier or retailer (if the 

installer or the authorized technician has collected the 

material from the retailer.)

 • After completing the installation, always carry out a 

functional test and provide the instructions on how to 

operate the air conditioner to the user.

 • Do not use the air conditioner in environments with 

hazardous substances or close to equipment that 

release free flames to avoid the occurrence of fires, 

explosions or injuries. 

 • The air conditioner should be used only for the 

applications for which it has been designed: the indoor 

unit is not suitable to be installed in areas used for 

laundry.

Safety Information

Safety Information

DB68-08953A-00_IM_DVM QMD_EU_EN_.indd   3

2020-02-10   오후 4:23:06

Содержание AM TNVD Series



































Отзывы: