background image

3

EN

G

LIS

H

 

f

Do not attempt to repair, move, alter or reinstall the unit by unauthorized personnel, these operations may cause product 

damage, electric shocks and fires.

 

f

Do not place containers with liquids or other objects on the unit.

 

f

All the materials used for the manufacture and packaging of the air to water heat pump are recyclable.

 

f

The packing material and exhaust batteries of the remote controller(optional) must be disposed of in accordance with local 

regulations.

 

f

The air to water heat pump containing a refrigerant must be disposed in authorized center or returned to retailer as special 

wastes.

 

f

Wear protective gloves to unpack, move, install, and service the unit to avoid your hands being injured by the edge of the parts.

 

f

Do not touch the internal parts (water pipes, refrigerant pipes, heat exchangers, etc) while running the units. And if you need to 

adjust and touch the units, have enough time for the unit can be cooled and be sure to wear protective gloves.

 

f

In case of refrigerant leakage, try to avoid getting in contact with the refrigerant because this could result in severe wounds.

 

f

When you install the Air to water heat pump in a small room, you must consider a proper ventilation to prevent a leakage level 

within the maximum permissible limit.

 - In that case, you may die from suffocation by some possibility.

 

f

Make sure to safely dispose of packing materials. Packing materials, such as nails and other metal or wooden pallets may cause 

children get injured.

 

f

Inspect the product shipped and check if damaged during transport. If the product has some damages, DO NOT INSTALL and 

immediately discuss about the damages with the carrier or retailer (if the installer or the authorized technician has collected 

the material from the retailer.)

 

f

Our units shall be installed in compliance with the spaces described in the installation manual, to ensure accessibility from both 

sides and allow repairs or maintenance operations to be carried out. If the units installed without complying with procedures 

described in manual, additional expenses can be asked because special harnesses, ladders, scaffolding or any other elevation 

system for repair service will NOT be considered part of the warranty and will be charged to the end customer.

 

f

Always make sure that the power supply is compliant with local safety standards.

 

f

Verify that the voltage and frequency of the power supply comply with the specifications and input power is sufficient to 

ensure the operation of any other domestic appliance connected to the same electric lines. Always verify that the cut-off and 

protection switches are suitably selected.

 

f

Always verify that electric connections (cable entry, section of leads, protections…) are compliant with the electric 

specifications and with the instructions provided in the wiring scheme. Always verify that all connections comply with the 

standards applicable to the installation of air to water heat pumps. Devices disconnected from the power supply should be 

completely disconnected in the condition of overvoltage category.

 

f

Do not connect the earth wire to the gas pipe or water pipe, lighting rod, surge absorber, or telephone earth wire. If earthing is 

not complete, it may cause an electric shock or fire.

 

f

Be sure to install both an earth leakage detector and circuit breaker with specified capacity in accordance with relevant local 

and national regulations.

 - If it is not installed properly, it may cause electric shocks and fire.

 

f

Make sure that the condensed water runs well out of the unit at low ambient temperature. Drain pipe and cond heater can 

frost/ice can not grow. If drain work is not effective for releasing condensed water, it can make the units get damaged by 

massive ice and system can be stop , covered by ice.

 

f

Install the power cable and communication cable of the indoor and outdoor unit at least 1m away from the electric appliance.

 

f

Protect the unit from rats or small animals. If an animal makes a contact with the electric parts, it can cause malfunctions, 

smoke or fire. Please instruct the customer to keep the area around the unit clean.

Содержание AEX060EDEHA








































Отзывы: