Samsung AC BN DKG Series Скачать руководство пользователя страница 30

Страница: 30 / 38

Installation Procedure

English

Instal

lation Pr

edur
e

Step 18 Setting indoor unit addresses

and installation options

Set the indoor unit address and installation option with

remote controller option. Set the each option separately

since you cannot set the ADDRESS setting and indoor unit

installation setting option at the same time. You need to

set twice when setting indoor unit address and installation

option.

Setting an indoor unit address

Press the and

buttons at the same time for more

than 3 seconds and then a Main menu will be displayed.

Press the

button to select and then press

button to enter a Sub-menu setting screen.

Press the

button to select and then press

button to enter a Indoor Address setting screen.

1 2 3 4

5 6

Data bit

NOTE

• The Main/RMC Address which is currently setting will

flicker.

• Data bit 1 and 2 present Indoor unit main address

checking

• Data bit 3 and 4 present Indoor unit main address

setting(outdoor unit reset is needed to set).

• Data bit 5 and 6 present Indoor unit RMC address setting/

checking.

Press the

button to set the Indoor unit Main/RMC

Address.

Press the button to save and complete the option

setting.

Press the

button to exit to normal mode.

NOTE

• Press the

button anytime during setup to exit

without setting.

• Address will not be applied if you don't press button.
• Setting Main/RMC Address of an Indoor unit is available

only with a Main wired remote controller.

Setting an indoor unit installation option

In order to check and set the indoor unit installation option

code use the wired remote controller and follow the

directions below.

Press the and

buttons at the same time for more

than 3 seconds and then a Main menu will be displayed.

Press the

button to select and then press

button to enter a Sub-menu setting screen.

Press the

button to select and then press

button to enter a Indoor unit installation option code setting

screen.

NOTE

• The first digit represents the page number and the

remaining five digits are installation option.

• The total option codes are 24 digits. You can set six digits

at a time and it is distinguished by page number (0, 1,

2, 3).

Press the

button to set the installation option code

in order. Press

button to go to the next page.

SEG1

SEG2

SEG3

SEG4

SEG5

SEG6

RESERVED

Exterior

temperature

sensor

Central

control

RESERVED

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

Drain pump

Use of Hot

Coil

Use of Heater

Controller

variables

for auxiliary

heater

RESERVED

SEG13

SEG14

SEG15

SEG16

SEG17

SEG18

External

control

External

control output

S-Plasma

ion

Buzzer

Number of

hours using

filter

SEG19

SEG20

SEG21

SEG22

SEG23

Individual

control of

a remote

controller

Heating

setting

compensation

RESERVED

Away Set

OFF Timer

Содержание AC BN DKG Series







































Результаты поиска

Содержание AC BN DKG Series

Отзывы:

Похожие инструкции для AC BN DKG Series

Бренды по названию

Популярные бренды

Samsung AC BN DKG Series, Руководство по установке

Результаты поиска

Содержание AC BN DKG Series

Отзывы:

Похожие инструкции для AC BN DKG Series

Бренды по названию

Популярные бренды