Samsung AC BN DKG Series Скачать руководство пользователя страница 24

Страница: 24 / 38

Installation Procedure

English

Instal

lation Pr

edur
e

Step 15 Optional: Extending the power

cable

Prepare the following tools.

Tools

Spec

Shape

Crimping pliers

MH-14

Connection sleeve

(mm)

20xØ6.5

(HxOD)

Insulation tape

Width 19

Contraction tube

(mm)

70xØ8.0

(LxOD)

As shown in the figure, peel off the shields from the rubber

and wire of the power cable.
• Peel off 20 mm of cable shields from the pre-installed

tube.

CAUTION

• For information about the power cable specifications for

indoor and outdoor units, refer to the installation manual.

• After peeling off cable wires from the pre-installed tube,

insert a contraction tube.

• If cable wires are connected without using connecting

sleeves, their contact area becomes reduced, or corrosion

develops on the outer surfaces of the wires (copper wires)

over a long time. This may cause an increase of resistance

(reduction of passing current) and consequently may

result in a fire.

120

180

120

Power cable

(Unit: mm)

Pre-installed

tube for the

power cable

Insert both sides of core wire of the power cable into the

connection sleeve.

• Method 1

: Push the core wire into the sleeve from both

sides.

• Method 2

: Twist the wire cores together and push it into

the sleeve.

Method 1

Connection sleeve

Method 2

Using a crimping tool, compress the two points and flip it over

and compress another two points in the same location.
• The compression dimension should be 8.0.

Compression

dimension

• After compressing it, pull both sides of the wire to make

sure it is firmly pressed.

5 mm

Method 1

Method 2

Compress it 4 times.

Apply heat to the contraction tube to contract it.

Method 2

Method 1

Contraction tube

Wrap it with the insulation tape twice or more and position

your contraction tube in the middle of the insulation tape.

Three or more layers of insulation are required.

After tube contraction work is completed, wrap it with the

insulation tape to finish.

Method 1

Method 2

IInsulation tape

Содержание AC BN DKG Series







































Результаты поиска

Содержание AC BN DKG Series

Отзывы:

Похожие инструкции для AC BN DKG Series

Бренды по названию

Популярные бренды

Samsung AC BN DKG Series, Руководство по установке

Результаты поиска

Содержание AC BN DKG Series

Отзывы:

Похожие инструкции для AC BN DKG Series

Бренды по названию

Популярные бренды