manualshive.com logo in svg

Samson Valve Series, Монтаж и эксплуатация

Поделиться
Скачать
Samson Valve Series Скачать руководство пользователя страница 16

Tighten nut (12) to fasten the plug and
sleeves:

Valve

DN 15 to 50

DN 65 to 80

Nut (12)

15 Nm

25 Nm

Remove the open-end wrench.

9. Align flange (5.4) to the bellows housing

(5.2), making sure the body gasket (1.2)
is correctly positioned.
Tighten nuts (1.1):

Valve

DN 15 to

25

DN 32 to

50

DN 65 to

80

Nuts (1.1)

M10

10 Nm

M12

30 Nm

M16

90 Nm

Firmly tighten the coupling nut (5.1) with
80 Nm.

10.

DN 15 to 50:

Thread the lock nut (6.2) and stem con-
nector nut (6.1) onto the top end of the
plug stem.
Adjust the stem connector nut (6.1) to
keep the dimension of 50 mm between
the top of the bellows assembly (5) and
the top of the stem connector nut (6.1)
when the plug stem is completely in-
serted into the valve. Refer to the dimen-
sional diagram on page 23.

Mount the actuator following the instructions
in the corresponding mounting and operat-
ing instructions.

4.2.2 Diverting valve

Disassembly

1. Unscrew the stem connector nut (6.1)

and lock nut (6.2) from the plug stem of
valves in DN 50 or smaller.

2. Unscrew the coupling nut (5.1) from the

bellows housing. Remove the nuts (1.1)
and lift off the flange (5.4).

3. Pull the bellows housing (5.2) with the

bellows assembly out of the body as far
as they will go. Place an open-end
wrench (SW 10 for

£

DN 50 or SW 13

for

³

DN 65) at the side on the hexagon

(X) or at the flattened area of the plug
stem to hold it stationary. Undo nut (12)
and remove wrench.

4. Unthread nut (12). Remove two lock

washers (12.2) and washer (12.1).

Maintenance–replacing parts

16

EB 8135/8136 EN

1.1

6.1
6.2

5.3
5
5.2

X

5.4

1.2

4.2
4.3
5.1

Fig. 13 ·  Valve bonnet with bellows seal

Содержание Valve Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды