background image

RSX Active Loudspeakers

3

1.  Read these instructions.

2.  Keep these instructions.

3.  Heed all warnings.

4.  Follow all instructions.

5.  Do not use this apparatus near water.

6.  Clean only with dry cloth.

7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) 

that produce heat.

9.  Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wid-

er than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong 
are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of 
the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the 

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the 

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid 
injury from tip-over.

13. Unplug the apparatus during lightening, sort or when unused for long periods of time.

14. Refer all servicing to qualified personnel. Service is required when the apparatus has been damaged in any way, such 

as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been 
exposed to rain or moisture, does not operate normally, or has been dropped.

15. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid such as vases 

shall be placed on the apparatus.

16. Caution-to prevent electrical shock, match wide blade plug wide slot fully insert.

17. Please keep a good ventilation environment around the entire unit.

18. POWER ON/OFF SWITCH: For products with a power switch, the power switch DOES NOT break the connection from 

the mains.

19. MAINS DISCONNECT: The plug should remain readily operable. For rack-mount or installation where plug is not acces-

sible, an all-pole mains switch with a contact separation of at least 3mm in each pole shall be incorporated into the 
electrical installation of the rack or building.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) AS THERE ARE NO 

USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral 

triangle is intended to alert the user to the presence of non-

insulated “dangerous voltage” within the product’s enclosure 

that may be of sufficient magnitude to constitute a risk of electric 

shock.
The exclamation point within an equilateral triangle is intended 

to alert the user to the presence of important operating and 

maintenance instructions in the literature accompanying the 

appliance.

ATTENTION

RISQUE DE CHOC ÉLECTRONIQUE - 

NE PAS OUVRIR

Important Safety Information

CAUTION

To prevent electric shock hazard, do not connect to mains power supply 

while grille is removed.

Содержание RSX M10a





















Отзывы: