background image

PRECAUCION

: Para reducir el riesgo de incendios o descargas, no permita que este aparato quede expuesto a la lluvia o la humedad. Para reducir el riesgo de 

descarga eléctrica, nunca quite la tapa ni el chasis. Dentro del aparato no hay piezas susceptibles de ser reparadas por el usuario. Dirija cualquier reparación al 

servicio técnico oficial. El símbolo del relámpago dentro del triángulo equilátero pretende advertir al usuario de la presencia de “voltajes peligrosos” no aislados 

dentro de la carcasa del producto, que pueden ser de la magnitud suficiente como para constituir un riesgo de descarga eléctrica a las personas. El símbolo de 

exclamación dentro del triángulo equilátero quiere advertirle de la existencia de importantes instrucciones de manejo y mantenimiento (reparaciones) en los 

documentos que se adjuntan con este aparato. 

Instrucciones importantes de seguridad 

1.    Lea todo este manual de instrucciones antes de comenzar a usar la unidad. 

2.   Conserve estas instrucciones para cualquier consulta en el futuro.  

 

3.   Cumpla con todo lo indicado en las precauciones de seguridad.  

4.   Observe y siga todas las instrucciones del fabricante.   

5. 

Nunca utilice este aparato cerca del agua o en lugares húmedos. 

6.    Limpie este aparato solo con un trapo suave y ligeramente humedecido. 

7. 

 No bloquee ninguna de las aberturas de ventilación. Instale este aparato de acuerdo a las instrucciones del fabricante. 

8.   No instale este aparato cerca de fuentes de calor como radiadores, calentadores, hornos u otros aparatos (incluyendo amplificadores) que produzcan calor.   

9.   No anule el sistema de seguridad del enchufe de tipo polarizado o con toma de tierra. Un enchufe polarizado tiene dos bornes, uno más ancho que el otro. 

Uno con toma de tierra tiene dos bornes normales y un tercero para la conexión a tierra. El borne ancho o el tercero se incluyen como medida de seguridad. 

Cuando el enchufe no encaje en su salida de corriente, llame a un electricista para que le cambie su salida anticuada.  

10.   Evite que el cable de corriente quede en una posición en la que pueda ser pisado o aplastado, especialmente en los enchufes, receptáculos y en el punto en 

el que salen de la unidad.  

11.   Desconecte de la corriente este aparato durante las tormentas eléctricas o cuando no lo vaya a usar durante un periodo de tiempo largo.  

12.  Dirija cualquier posible reparación solo al servicio técnico oficial. Deberá hacer que su aparato sea reparado cuando esté dañado de alguna forma, como si 

el cable de corriente o el enchufe están dañados, o si se han derramado líquidos o se ha introducido algún objeto dentro de la unidad, si esta ha quedado 

expuesta a la lluvia o la humedad, si no funciona normalmente o si ha caído al suelo.

Instrucciones de seguridad / Istruzioni di Sicurezza

ATTENZIONE

: per ridurre il rischio di incendio o di scariche elettriche, non esponete questo apparecchio a pioggia o umidità. Per ridurre il pericolo di scariche 

elettriche evitate di rimuoverne il coperchio o il pannello posteriore. Non esistono all'interno dell'apparecchio parti la cui regolazione è a cura dell'utente. Per even-

tuale assistenza, fate riferimento esclusivamente a personale qualificato. Il fulmine con la punta a freccia all'interno di un triangolo equilatero avvisa l'utente della 

presenza di "tensioni pericolose" non isolate all'interno dell'apparecchio, tali da costituire un possibile rischio di scariche elettriche dannose per le persone. Il punto 

esclamativo all'interno di un triangolo equilatero avvisa l'utente della presenza di importanti istruzioni di manutenzione (assistenza) nella documentazione che 

accompagna il prodotto.

Importanti Istruzioni di Sicurezza

1.   Prima di usare l'apparecchio, vi preghiamo di leggerne per intero le istruzioni. 

2.   Conservate tali istruzioni per una eventuale consultazione futura.

3.   Vi preghiamo di rispettare tutte le istruzioni di sicurezza. 

4.   Seguite tutte le istruzioni del costruttore.   

5.  Non usate questo apparecchio vicino ad acqua o umidità. 

6.   Pulite l'apparecchio esclusivamente con un panno asciutto.  

7.   Evitate di ostruire una qualsiasi delle aperture di ventilazione. Posizionatelo seguendo le istruzioni del costruttore. 

8.    Non posizionatelo vicino a sorgenti di calore come radiatori, scambiatori di calore, forni o altri apparecchi (amplificatori compresi) in grado di generare calore.

9.    Non disattivate la protezione di sicurezza costituita dalla spina polarizzata o dotata di collegamento a terra. Una spina polarizzata è dotata di due spinotti, uno 

più piccolo ed uno più grande. Una spina dotata di collegamento a terra è dotata di due spinotti più un terzo spinotto di collegamento a terra. Questo terzo 

spinotto, eventualmente anche più grande, viene fornito per la vostra sicurezza. Se la spina fornita in dotazione non si adatta alla vostra presa, consultate un 

elettricista per la sostituzione della presa obsoleta.  

10.  Proteggete il cavo di alimentazione in modo che non sia possibile camminarci sopra né piegarlo, con particolare attenzione alle prese, ai punti di collegamento 

e al punto in cui esce dall'apparecchio.  

11.   Staccate l'apparecchio dalla alimentazione in caso di temporali o tempeste o se non lo usate per un lungo periodo.  

12.   Per l'assistenza, fate riferimento esclusivamente a personale qualificato. È necessaria l'assistenza se l'apparecchio ha subito un qualsiasi tipo di danno, come 

danni al cavo o alla spina di alimentazione, nel caso in cui sia stato versato del liquido o siano caduti oggetti al suo interno, sia stato esposto a pioggia o 

umidità, non funzioni correttamente o sia stato fatto cadere.

Copyright 2009 - Samson Technologies Corp.

Printed March, 2009 v1

Samson Technologies Corp.

45 Gilpin Avenue

Hauppauge, New York 11788-8816

Phone: 1-800-3-SAMSON (1-800-372-6766)

Fax: 631-784-2201 

www.samsontech.com

Содержание L2000

























Отзывы: