Samson 2404-2 Скачать руководство пользователя страница 45

Страница: 45 / 76

EB 2540 EN

6-1

Start-up

The work described in this section is only to
be performed by personnel appropriately

qualified to carry out such tasks.

Risk of burn injuries due to hot or cold com-

ponents and pipeline.

Regulator components and the pipeline may
become very hot or cold. Risk of burn inju

ries.

Allow components and pipelines to cool
down or warm up to the ambient tem

perature.

Wear protective clothing and safety
gloves.

Risk of personal injury due to pressurized

components and process medium being dis-

charged.

Do not loosen the control line while the
valve is pressurized.

Risk of hearing loss or deafness due to loud

noise.

Noise emission (e.g. cavitation or flashing)

may occur during operation caused by the
process medium and the operating condi-
tions.

Wear hearing protection when working

near the valve.

WARNING

Re
Risk of personal injury due to process me-

dium escaping.

Do not start up the regulator until all

parts have been mounted.

Before start-up or putting the valve back into

service, make sure the following conditions
are met:

−

The regulator is properly installed into
the pipeline (see the 'Installation' sec-
tion).

−

The leak and function tests have been
completed successfully (see the 'Testing
the regulator' section).

−

The prevailing conditions in the plant

section concerned meet the regulator siz

ing requirements (see information under
'Intended use' in the 'Safety instructions
and measures' section).

Damage to the regulator/plant due to the

use of the incorrect supply medium.

Only use compressed air or inert gas as
the supply pressure.

DANGER

NOTICE

Содержание 2404-2













































































Результаты поиска

Содержание 2404-2

Отзывы:

Похожие инструкции для 2404-2

Бренды по названию

Популярные бренды

Samson 2404-2, Монтаж и эксплуатация

Результаты поиска

Содержание 2404-2

Отзывы:

Похожие инструкции для 2404-2

Бренды по названию

Популярные бренды