background image

 

SAMLEX AMERICA, INC.

 |  3

SECTION 1  

|  Important Safety Instructions

CAUTION: RISK OF ELECTRIC SHOCK! DO NOT OPEN!

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE  
TO RAIN OR MOISTURE. THERE ARE NO USER SERVICEABLE PARTS INSIDE—REFER TO 
QUALIFIED SERVICE PERSONNEL.

The following safety symbols will be used in this manual to highlight safety & information:

 

 

 

WARNING!

Indicates possibility of physical harm to the user in case of non-compliance.

 

!

  CAUTION!

Indicates possibility of damage to the equipment in case of non-compliance.

 

i

    

INFO

Indicates useful supplemental information. 

Please read before using your power supply:

1.  It Is recommended that you return your power supply to a qualified Samlex dealer for any 

service or repair. Incorrect assembly may result in electric shock or fire.

2.  To reduce the risk of electric shock, unplug the power supply from the outlet before  

attempting any maintenance or cleaning. Turning off controls will not reduce this risk.

3.  An extension cord should not be used unless absolutely necessary. 

If an extension cord must 

be used, make sure that the pins on the plug are the same number, size and shape as those 
of the original power supply plug.

4.  Place the unit in an area that will allow air to flow freely around the unit. 

DO NOT BLOCK 

OR OBSTRUCT

 vent openings on the side/bottom of the unit.

5.  Keep the unit away from moisture and water.

6. 

NEVER operate the units in parallel.

 

 

WARNING!

Your power supply should be grounded to reduce the risk of electric shock. The power  
supply comes with a detachable power cord that has a  3-prong, grounded male plug  
(NEMA5-15P). The round prong of the plug gets connected to the chassis of the unit. When the 
power cord is plugged into the corresponding 3 slot female receptacle (NEMA5-15R), the chassis 
of the unit is automatically connected to the earth ground through the equipment grounding 
conductor that is connected to the round slot of the female NEMA5-15R receptacle.

The power cord must be plugged into a NEMA5-15R outlet that is properly installed and 
grounded in accordance with all local codes and ordinances. Never alter the power cord that has 
been provided. If the plug of the cord will not fit the outlet, have a proper outlet installed by a 
qualified electrician. Improper connection can result in risk of electric shock.

DO NOT USE THE POWER SUPPLY FOR DIRECT CHARGING OF BATTERY OR DIRECT  
CONNECTION TO A BATTERY FOR BATTERY BACK-UP. (

Please read the section on “Battery 

Charging & Battery Back-up”

).

Содержание SEC-1235

















Отзывы: