Samoa LARIUS OMEGA Скачать руководство пользователя

Страница: 14 / 38

www.larius.com

Omega 23:1-30:1

ED.

04 - 09/2021 - Cod. 150150

Q12

Q13

Q14

Q13

Q12

Q15

Q16

Q10

Q11

Q10

Q4
Q5

Fig. 1Q

Coupling sleeve

• Unscrew the coupling sleeve so as to disconnect the pumping

group from the motor.

• Disconnect the air feed pipe to the pump.
• Unscrew the fitting (

) and the sleeve (

Q2).

• Turn counterclockwise the screws (

) [take care of the washers

(

) and remove the covering (

• Unscrew the two ring nuts (

) from the mount (

Q7)

• Turn counterclockwise the screws (

) [take care of the washers

(

)] and extract the mount (

) together with the rollers (

Q10

)

and the pins (

Q11

• Extract the spring (

Q12

), the spring guide rod (

Q13

) and the

roller pushing piston (

Q14

). Ensure the spring slides freely on the

guide rod, the guide rod slides into the roller pushing piston and

this last slides into the mount hole. Replace possible damaged

parts.

• Check the roller (

Q10

) and the pin (

Q11

) are undamaged. Replace

them if damaged.

• Remove and check the rubber pad (

Q15

) and the washer (

Q16

)

Always close the compressed air supply
and release the pressure in the plant before
disassembling the pneumatic motor of the pump.

DISASSEMBLY OF THE
PNEUMATIC MOTOR

Содержание LARIUS OMEGA







































Результаты поиска

Содержание LARIUS OMEGA

Отзывы:

Похожие инструкции для LARIUS OMEGA

Бренды по названию

Популярные бренды

Samoa LARIUS OMEGA, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LARIUS OMEGA

Отзывы:

Похожие инструкции для LARIUS OMEGA

Бренды по названию

Популярные бренды