SAMES KREMLIN REXSON SH0910 Скачать руководство пользователя страница 43

Страница: 43 / 50

Disassembly / Reassembly Operation

Reassembly of the fluid section



Lubricate the wetting cup seals and the piston head seals,



Locate the seals (9) inside the pump body (7) of the valve
body (21)



Slide the piston rod assembly (15) inside the pump body (7),
push it upwards;



Screw the cylinder (10) to stop,



Screw the shovel rod (31) change the pin (23),



Screw the valve body (21) on the cylinder (10) to stop,



Slide the lower valve (28)

on the shovel rod (31) and screw

slightly the cup nut (24),



Install the seal (18) in the valve body (21),



Install the seat (30) and push it in its housing,



Locate the seal (36) inside the valve body (21),



Screw the filling tube (37) to stop,



Install the spacer (32), the washer (33) and the shovel (34)
on the shovel rod (31),



Screw the lock nut (35),



Screw slightly the cup (5),



Re assemble the pump to the pneumatic motor according
to the instructions of the pump instruction manual.

Nota: The quantity of seals of the packings (11) & (45)
depends upon the used package of seals.

Before each reassembly



Clean the parts with the appropriate cleaning solvent.



Fit new seals if necessary, after greasing them.



Grease the piston and the inside of the cylinder to avoid
damaging the seals.



Fit new parts if necessary.

Содержание REXSON SH0910



















































Результаты поиска

Содержание REXSON SH0910

Отзывы:

Похожие инструкции для REXSON SH0910

Бренды по названию

Популярные бренды

SAMES KREMLIN REXSON SH0910, Руководство пользователя

Результаты поиска

Содержание REXSON SH0910

Отзывы:

Похожие инструкции для REXSON SH0910

Бренды по названию

Популярные бренды