SAMES KREMLIN REXSON SH0910 Скачать руководство пользователя страница 28

Страница: 28 / 50

Installation

Installation

7.1

Handling

Fluid sections of great weight and size must be handled
with suitable lifting equipment.

7.2

Connections subsets



These fluid sections are intended to be coupled to motors
(pneumatic or hydraulic) compatible stroke.



It is imperative to comply with an air motor / hydraulic
combination provided by SAMES KREMLIN



Make sure that all connections of the pump and fluid
section components - cables, hoses and pipes - are installed
in such a way that they do not cause people to fall.



Make sure that the order in which the cables, hoses and
pipes are connected is in accordance with the connection
diagram.



Make sure that all cable connectors, hose and pipe
connections are correctly fitted.



Remember that unconnected or incorrectly connected
cables, hoses and pipes can lead to malfunctions that
endanger the safety of operating personnel.

7.2.1

Fluid supply connection



If the supply pressure is higher than the max. pressure, it is
necessary to install a fluid pressure regulator the closest
possible of the equipment.



Ensure that a short product hose reduces pressure
fluctuations and pressure drops.



Make sure that the fluid supply is properly made. The
nominal size of the fitting to be used depends on the
nominal size of the fluid hose.

Содержание REXSON SH0910



















































Результаты поиска

Содержание REXSON SH0910

Отзывы:

Похожие инструкции для REXSON SH0910

Бренды по названию

Популярные бренды

SAMES KREMLIN REXSON SH0910, Руководство пользователя

Результаты поиска

Содержание REXSON SH0910

Отзывы:

Похожие инструкции для REXSON SH0910

Бренды по названию

Популярные бренды